Show Posts
1
General discussion forum / Lost display with 706 after router reboot
« on: 2012-01-20, 04:52:40 »
I have run remoterig for about 5 days without any problem. I had to reboot my router today and since then there is no display and no audio. My status looks like:
Info:
Company Microbit
Product 1258
PID 4
Hardware 6
Software 2.50
Bootloader 1.9
Compiler 4.1.2 (WinARM 4/2007)
Build Dec 15 2011 15:15:54
ROM/RAM 372540/50740
ETH-RAM 2944 (max 3kB!)
ResetSrc 0 [3]
Uptime 325
Serial number 3927
MAC address 00:1e:......
IP address 192.168.1.227
Netmask 255.255.255.0
Gateway 192.168.1.1
DNS 192.168.1.1
Status:
Name Value
Control panel OFF
Radio OFF
Connection status OK
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status OK(44)
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
Current audio packet size 20
Current audio quality 2 - Linear 16 bits 8 kHz
External IP <not shown>
SIP Out port 1202 <----------------- bad port. reset to 8001 on each end and shows ok now.
SIP In port 8000 This port set to 8101 also now.
Audio Out port 8100
Audio In port 8100
Command Out port 8200
Command In port 8200
External SIP In port 8000
External Audio In port 8100
External Cmd In port 8200
Other party <not shown but correct>
Input 0 High
Input 1 High
Input 2 High
Output 0 High
Output 1 Low
Output 2 Low
DNS status OK, <not shown but okay IP address>
Active profile: Default
PTT status: OFF
Ethernet port is rapid flashing green.
AUX port is solid yellow.
Notice the 1202 SIP port. These boxes are picking up the wrong port numbers. The port were 8000 on both ends, but one side assigned 1202. I have other ports assign like 23458 and 54-something in the past which isn't even close to the port numbers that were assigned in the box. Where are these coming from? I went in and set SIP to 8001 on each end and they show up correct now in the status.
The system will reboot occasionally and beep but restores back to the same situation.
I have read all the postings on here about ports and other things and tried them all. If you notice, I have ports now at 8000, 8100 and 8200. There are no errors but still not display or control via the panel. With the ports at 11000, 12000 range I would have errors on the RTP status.
Now, I can watch the radio on the other side and pressing my power button will turn it on and off. But, there is no audio on my end and no panel display / control other than power.
it was working fine and am a loss as to figuring out the problem before I give up on these boxes. The radios are separated by 1700 miles so can just drive over there.
Any thoughts or help?
Tnx
Info:
Company Microbit
Product 1258
PID 4
Hardware 6
Software 2.50
Bootloader 1.9
Compiler 4.1.2 (WinARM 4/2007)
Build Dec 15 2011 15:15:54
ROM/RAM 372540/50740
ETH-RAM 2944 (max 3kB!)
ResetSrc 0 [3]
Uptime 325
Serial number 3927
MAC address 00:1e:......
IP address 192.168.1.227
Netmask 255.255.255.0
Gateway 192.168.1.1
DNS 192.168.1.1
Status:
Name Value
Control panel OFF
Radio OFF
Connection status OK
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status OK(44)
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
Current audio packet size 20
Current audio quality 2 - Linear 16 bits 8 kHz
External IP <not shown>
SIP Out port 1202 <----------------- bad port. reset to 8001 on each end and shows ok now.
SIP In port 8000 This port set to 8101 also now.
Audio Out port 8100
Audio In port 8100
Command Out port 8200
Command In port 8200
External SIP In port 8000
External Audio In port 8100
External Cmd In port 8200
Other party <not shown but correct>
Input 0 High
Input 1 High
Input 2 High
Output 0 High
Output 1 Low
Output 2 Low
DNS status OK, <not shown but okay IP address>
Active profile: Default
PTT status: OFF
Ethernet port is rapid flashing green.
AUX port is solid yellow.
Notice the 1202 SIP port. These boxes are picking up the wrong port numbers. The port were 8000 on both ends, but one side assigned 1202. I have other ports assign like 23458 and 54-something in the past which isn't even close to the port numbers that were assigned in the box. Where are these coming from? I went in and set SIP to 8001 on each end and they show up correct now in the status.
The system will reboot occasionally and beep but restores back to the same situation.
I have read all the postings on here about ports and other things and tried them all. If you notice, I have ports now at 8000, 8100 and 8200. There are no errors but still not display or control via the panel. With the ports at 11000, 12000 range I would have errors on the RTP status.
Now, I can watch the radio on the other side and pressing my power button will turn it on and off. But, there is no audio on my end and no panel display / control other than power.
it was working fine and am a loss as to figuring out the problem before I give up on these boxes. The radios are separated by 1700 miles so can just drive over there.
Any thoughts or help?
Tnx