Messages

1

Configuration, RRC 1258 / RRC1258-MkII RJ45 AUX/MIC leds blinking - burned?

« on: 2024-11-13, 19:30:26 »

hello

continuing with my station problems, today I noriced that the remoterig box at the remote side is not working.

I bring it at home to test it, connected to power and the red and yellow leds on the RJ45 AUX/MIC are blinking

I connected it to Microbit setup manager and I read a text in red "look ForHids()"

I do GET FROM DEVICE and nothing happen

Any idea whatīs the problem and how to solve it?

thanks in advance!!

73,
Jorge
CX6VM/CW5W

2

Configuration, RRC 1258 / Re: RRC1258-MkII IP addresses on diferent LANs

« on: 2024-11-12, 00:22:44 »

Mike

I remember that sometime ago when my internet link was broken, I use a Movistar router, it worked, I just needed to setup a dydns to have it working

I will ask a friend to set it up for me.

thanks!
Jorge

3

Configuration, RRC 1258 / Re: RRC1258-MkII IP addresses on diferent LANs

« on: 2024-11-10, 16:04:34 »

thanks Mike

this is very bad news for me :-(

73,
Jorge

4

Configuration, RRC 1258 / RRC1258-MkII IP addresses on diferent LANs

« on: 2024-11-06, 20:58:31 »

Hello

after many years using RRC1258-MkII on the same network (with an internet link from my house to the remote site), now I will move to Starlink on the remote site.

My network use 192.168.0.x addresses, and my remoterig boxes use 192.168.0.169 and 192.168.0.170

My new network on the remote site, with Starlink and a router, use 192.168.10.x

So my question is how I need to setup the remoterig and routers to have remoterig working? With 192.168.0.x on the home and 192.168.10.x on the remote side

thanks in advance

73,
Jorge
CX6VM/CW5W

5

General discussion forum / Re: RRC1258, K3/0 mini no RF output on any mode

« on: 2024-03-08, 02:19:34 »

thanks Mike

tomorrow will go to the remote site and check what happen

73,
Jorge

6

General discussion forum / Re: Mitch - DJ0QN SK

« on: 2024-02-29, 22:55:59 »

just know about this, very sad news

a great guy, always helping in this forum

RIP

73,
Jorge
CX6VM/CW5W

7

General discussion forum / RRC1258, K3/0 mini no RF output on any mode

« on: 2024-02-29, 22:11:45 »

Hello

today i noticed that my K3/0 mini is not transmitting on any mode, SSB, CW, FT8

Radio go on TX, but no RF output

I can receive without problem on SSB, CW and also FT8, but incredible that I cannot transmmit

Any idea what to check?, MIC gain is OK, POWER is OK

thanks
Jorge
CX6VM/CW5W

8

Konfiguration av RRC 1258 / Re: RRC1258, K3/0 mini no SSB output

« on: 2023-11-08, 20:36:34 »

Hello Mike

yes, I have the original Elecraft cables

today I finally set MIC SEL to rP.H, this was the way to do FT8 that also was not working yesterday after the changes I did

I am emailing both files to you

thanks!

Jorge

9

Konfiguration av RRC 1258 / Re: RRC1258, K3/0 mini no SSB output

« on: 2023-11-08, 01:06:33 »

hello

finally I have time to go to the remote site

I took MH2 Elecraft microphone

I tested on local K3, a radio that is alone to do radio directly from the contest station, and it works OK.

Then I connected the MH2 on the K3 that I use to do remote, it was ON and MH2 was working perfectly, going full power output

Then I arrive at home, connected the MH2 microphone on the K3/0 mini, and doesnīt work?

No idea what is wrong

Bottom of the line, now I cannot TX on FT8!, I need to review what I modify on the K3 menu that is not TX. Radio go on TX but no output

thanks!
Jorge
CX6VM/CW5W

10

Konfiguration av RRC 1258 / Re: RRC1258, K3/0 mini no SSB output

« on: 2023-10-11, 00:03:32 »

Hello

I imported a good setting files on each RRC1258 boxes.

Maybe the audio cable on the remote side is disconnected?

Donīt know what more to check in my side

73,
Jorge
CX6VM

11

Konfiguration av RRC 1258 / Re: RRC1258, K3/0 mini no SSB output

« on: 2023-10-10, 18:12:32 »

hello Mike

I tried with all options

MIC SEL = rP.H
MIC SEL = LInE In
MIC SEL = FP.H bIAS

etc

73,
Jorge

12

Konfiguration av RRC 1258 / RRC1258, K3/0 mini no SSB output

« on: 2023-10-10, 02:52:50 »

Hello

My setup with K3/0Mini and remoterig boxes was working fine

Now after some months not doing a phone qso, I tried again but no audio out. I am usinh MH2 microphone with the K3/0 mini. I can see my amplifier client showing 1200 watts, but no ALC bars on K3 display, I was monitoring me but not listening my voice.

I had some storaged messages on K3īs M1, M2, M3 and M4 memories and the work OK, perfect output audio showing ALC bars on my K3 display

Any idea what may I check?

thanks!

Jorge
CX6VM

13

Konfiguration av RRC 1258 / Re: IP setup problem

« on: 2023-07-18, 20:17:53 »

Mello Mike

myipaddress show
Your Hostname:
152.156.165-134-dynamic.movinet.com.uy

Router Status
Active LinkWWAN1
Uptime2 days, 00:09:01
IP Address152.156.165.134/255.255.255.252
Gateway152.156.165.133
DNS200.58.141.163 200.58.157.11

now is working, BUT I didnīt changed anything!. Will see when it stop working again

thanks!

73,
Jorge

14

Konfiguration av RRC 1258 / IP setup problem

« on: 2023-07-18, 19:19:04 »

Hello

I know this was discusses many times, but I couldnīt figure out who to solve it.

I have K3/0 Mini and remoterig boxes working perfectly on the SAME network

My internet link to the station broken, so I installed another internet system at the station

So now I have diferent networks on both sides

I have a dyndns service, I setup it on the remote router and I add it on my local remoterig settings (192.168.0.169)

Sometimes it worked, but now is not working, so i think is this IP changing but I couldnīt figure out how to have it working

I apreciate any help to set up it

thanks in advance!

73,
Jorge
CX6VM/CW5W

15

Configuration of Routers, Firewalls, etc / Re: Amper 2000 4L DDNS help

« on: 2021-10-06, 18:42:05 »

hello Mitch

I start over

I did that, but on http://ddns.remoterig.com/status/index.php I received Microbit DDNS Result xxxxxxx not found!

So seems remoterig dynamic dns service is not working?

73,
Jorge
CX6VM/CW5W