Show Posts
1
Configuration, RRC 1258 / Transparent Serial Channel on 1258 MKII
« on: 2012-04-03, 17:40:13 »
I am setting up a remote control for an AOR AR8600 Communications Receiver for our Ham Shack by using two remoterig RRC-1258 MKII. Both control and Radio units have firmware 2.5 installed. Their Serial numbers are 4073 and 4058, respectively. The radio is feeding audio through the network to the speakers attached to the control unit. I am able to control the AOR via a Hyperterminal, but can not receive data back from the radio.
I have used Program mode 11 on both units, and have used Program Mode 0 on the Radio unit and mode 11 on the control unit with the same results. I am using Com2, Mode 3 on both ends with the Com0 (USB) and Com1 inactive. When I connect the serial cable from the computer straight through to the AOR, I am able to control the radio and receive data back from it, but when I sever that link and attach serial cable to COM2 on both remoterig 1258-MKII units, with everything else the same, I can not receieve data back from the radio. I am not looking for anything fancy, I simply need Transparent RS-232 Control and Response, and audio return.
The settings for the Radio control are:
Name Value
Radio OFF
Connection status OK
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(59)
UDP cmd status OK(39)
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
Current audio packet size 20
Current audio quality 2 - Linear 16 bits 8 kHz
SIP Out port 5060
SIP In port 5060
Audio Out port 11000
Audio In port 11000
Command Out port 12000
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 152.75.16.81
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
Dynamic DNS status Unknown
Ping status (watchdog) Off
DNS status Error, failed to resolve remoterig.com!
Active profile: Default
PTT status: OFF
I have used Program mode 11 on both units, and have used Program Mode 0 on the Radio unit and mode 11 on the control unit with the same results. I am using Com2, Mode 3 on both ends with the Com0 (USB) and Com1 inactive. When I connect the serial cable from the computer straight through to the AOR, I am able to control the radio and receive data back from it, but when I sever that link and attach serial cable to COM2 on both remoterig 1258-MKII units, with everything else the same, I can not receieve data back from the radio. I am not looking for anything fancy, I simply need Transparent RS-232 Control and Response, and audio return.
The settings for the Radio control are:
Name Value
Radio OFF
Connection status OK
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(59)
UDP cmd status OK(39)
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
Current audio packet size 20
Current audio quality 2 - Linear 16 bits 8 kHz
SIP Out port 5060
SIP In port 5060
Audio Out port 11000
Audio In port 11000
Command Out port 12000
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 152.75.16.81
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
Dynamic DNS status Unknown
Ping status (watchdog) Off
DNS status Error, failed to resolve remoterig.com!
Active profile: Default
PTT status: OFF