Show Posts
1
Configuration of Routers, Firewalls, etc / Can't Connect Remotely
« on: 2012-07-22, 00:45:28 »
Please Help
My IC-2820 will not connect remotely. It does work fine on local network. The control is going through a Cradlepoint MBR95 with a Verizon 3g card, and the radio side is using a Linksys WRT160n. On the Radio side, the PWR light is on steady, but there is a flashing amber LED on the AUX/MIC. I read that I should disable SIP/ALG but that doesn't seem to be an option on either of my routers. Could that be the problem?
Any suggestions?
Thanks
Steve
KJ4YGY
*************************************************************************************
Info
Name Value
Company Microbit
Product 1258
PID 4
Version 5
HW 6
Software 2.60
Bootloader 1.9
Compiler 4.6.2
Build Jun 18 2012 14:23:22
ROM/RAM 435604/56456
ETH-RAM 2944 (max 3kB!)
ResetSrc 0 [3]
Uptime 197
Serial number 4682
MAC address 00:1e:fd:01:88:ea
IP address 192.168.1.228
Netmask 255.255.255.0
Gateway 192.168.1.1
DNS 192.168.1.1
Wi-Fi network module not present
Settings
Unit ID (Banner)
DHCP 0
IP 192.168.1.228
Netmask 255.255.255.0
Gateway 192.168.1.1
Dns server 192.168.1.1
Extern IP/Host
Eth-type 5
Web page user
Web page pwd
Program mode 9
Control panel 0
Sip password XXXXXXXX
Sip contact
Auto connect 0
Audio quality 2
Audio dual-rx 1
Codec out gain 255
Codec inp gain 0
Codec inp HPF Hz 3
Codec inp preamp 1
COM0 baudrate 38400
COM0 data bits 8
COM0 stop bits 1
COM0 parity 0
COM0 Program mode 3 char timeout 2
Use USB Com Port as COM0 0
COM1 mode 0
COM1 baudrate 9600
COM1 data bits 8
COM1 stop bits 1
COM1 parity 0
COM1 rts/cts 0
COM1 terminator (hex) 00
Use USB Com Port as COM1 0
COM2 mode 0
COM2 baudrate 9600
COM2 data bits 8
COM2 stop bits 1
COM2 parity 0
COM2 terminator (hex) 00
Use USB Com Port as COM2 0
UDP cmd port 12000
UDP audio port 11000
SIP port 5000
Web server port 80
Telnet server port 23
Rx jitter buffer size 4
Rx jitter delay 3
Audio packet size (ms) 20
RTP tx mode 0
Debug level 0
Disable audio tones 0
Full duplex 0
PTT-off mute delay 0
IP Type-of-Service (dec) 0
Yaesu power-on/off 0
Elecraft advanced 0
Dynamic DNS check interval 10
Dynamic DNS host name 0
Own host name XXXXXXXX.ham-radio-op.net
Username XXXXXXXX
Password XXXXXXXX
Enable 0
Speed wpm [0/10-40] 0
Iambic 1
Paddle reverse 0
Weight [25-40] 30
Side tone hz [0,300-1500] 800
Side tone -db [50-0] 20
Lf delay ms [0-500] 0
Key delay ms [0-250] 0
PTT activated by Keyer 0
PTT tail delay ms [0-999] 0
Speed pot min wpm [5-99] 10
Speed pot max wpm [5-99] 40
IN0 mode 0
OUT0 mode 0
OUT0 mode 0
OUT1 mode 0
OUT1 mode 0
OUT2 mode 0
OUT2 mode 0
USB RTS as PTT 0
USB DTR as CW 0
Enable ping watchdog 0
IP address to ping
Ping interval (seconds) 300
Startup delay (seconds) 300
Failure count to reboot 3
1: Name (SSID)
1: Password (PSK)
2: Name (SSID)
2: Password (PSK)
3: Name (SSID)
3: Password (PSK)
4: Name (SSID)
4: Password (PSK)
5: Name (SSID)
5: Password (PSK)
6: Name (SSID)
6: Password (PSK)
7: Name (SSID)
7: Password (PSK)
8: Name (SSID)
8: Password (PSK)
Status
Name Value
Radio ON
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 1
SIP Out port 5000
SIP In port 5000
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5000
External Audio In port 11000
External Cmd In port 12000
Other party 0.0.0.0
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
Dynamic DNS status Error, code 4
Ping status (watchdog) Off
DNS status Error, failed to resolve remoterig.com!
Active profile: Default
PTT status: OFF
****************************************************************
Info
Name Value
Company Microbit
Product 1258
PID 0
Version 5
HW 6
Software 2.60
Bootloader 1.9
Compiler 4.6.2
Build Jun 18 2012 14:23:22
ROM/RAM 435604/56456
ETH-RAM 2944 (max 3kB!)
ResetSrc 0 [3]
Uptime 254
Serial number 4700
MAC address 00:1e:fd:01:88:fc
IP address 192.168.0.227
Netmask 255.255.255.0
Gateway 192.168.0.1
DNS 192.168.0.1
Wi-Fi network module not present
Settings
Unit ID (Banner) IC-2820
DHCP 0
IP 192.168.0.227
Netmask 255.255.255.0
Gateway 192.168.0.1
Dns server 192.168.0.1
Extern IP/Host
Eth-type 5
Web page user
Web page pwd
Program mode 9
Control panel 1
Sip password XXXXXXXX
Sip contact XXXXXXXX.ham-radio-op.net
Auto connect 1
Audio quality 2
Audio dual-rx 0
Codec out gain 255
Codec inp gain 18
Codec inp HPF Hz 3
Codec inp preamp 1
COM0 baudrate 38400
COM0 data bits 8
COM0 stop bits 1
COM0 parity 0
COM0 Program mode 3 char timeout 2
Use USB Com Port as COM0 0
COM1 mode 0
COM1 baudrate 9600
COM1 data bits 8
COM1 stop bits 1
COM1 parity 0
COM1 rts/cts 0
COM1 terminator (hex) 00
Use USB Com Port as COM1 0
COM2 mode 0
COM2 baudrate 9600
COM2 data bits 8
COM2 stop bits 1
COM2 parity 0
COM2 terminator (hex) 00
Use USB Com Port as COM2 0
UDP cmd port 12000
UDP audio port 11000
SIP port 5000
Web server port 80
Telnet server port 23
Rx jitter buffer size 16
Rx jitter delay 15
Audio packet size (ms) 20
RTP tx mode 0
Debug level 0
Disable audio tones 0
Full duplex 0
PTT-off mute delay 0
IP Type-of-Service (dec) 0
Yaesu power-on/off 0
Elecraft advanced 0
Dynamic DNS check interval 0
Dynamic DNS host name 0
Own host name
Username
Password
Enable 0
Speed wpm [0/10-40] 0
Iambic 1
Paddle reverse 0
Weight [25-40] 30
Side tone hz [0,300-1500] 800
Side tone -db [50-0] 20
Lf delay ms [0-500] 0
Key delay ms [0-250] 0
PTT activated by Keyer 0
PTT tail delay ms [0-999] 0
Speed pot min wpm [5-99] 10
Speed pot max wpm [5-99] 40
IN0 mode 0
OUT0 mode 0
OUT0 mode 0
OUT1 mode 0
OUT1 mode 0
OUT2 mode 0
OUT2 mode 0
USB RTS as PTT 0
USB DTR as CW 0
Enable ping watchdog 0
IP address to ping
Ping interval (seconds) 300
Startup delay (seconds) 300
Failure count to reboot 3
1: Name (SSID)
1: Password (PSK)
2: Name (SSID)
2: Password (PSK)
3: Name (SSID)
3: Password (PSK)
4: Name (SSID)
4: Password (PSK)
5: Name (SSID)
5: Password (PSK)
6: Name (SSID)
6: Password (PSK)
7: Name (SSID)
7: Password (PSK)
8: Name (SSID)
8: Password (PSK)
Status
Name Value
Control panel ON
Radio ON
Connection status Disconnected
SIP status Unknown(1)
Last SIP error SIP Error
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 5
Rx Jitter buffer size 16
Rx Jitter delay 15
Dual Rx 0
SIP Out port 5000
SIP In port 5000
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5000
External Audio In port 11000
External Cmd In port 12000
Other party 192.168.2.2
Input 0 High
Input 1 High
Input 2 High
Output 0 High
Output 1 Low
Output 2 Low
DNS status OK, XXXXXXXX.ham-radio-op.net = 192.168.2.2
Active profile: Default
PTT status: OFF
My IC-2820 will not connect remotely. It does work fine on local network. The control is going through a Cradlepoint MBR95 with a Verizon 3g card, and the radio side is using a Linksys WRT160n. On the Radio side, the PWR light is on steady, but there is a flashing amber LED on the AUX/MIC. I read that I should disable SIP/ALG but that doesn't seem to be an option on either of my routers. Could that be the problem?
Any suggestions?
Thanks
Steve
KJ4YGY
*************************************************************************************
Info
Name Value
Company Microbit
Product 1258
PID 4
Version 5
HW 6
Software 2.60
Bootloader 1.9
Compiler 4.6.2
Build Jun 18 2012 14:23:22
ROM/RAM 435604/56456
ETH-RAM 2944 (max 3kB!)
ResetSrc 0 [3]
Uptime 197
Serial number 4682
MAC address 00:1e:fd:01:88:ea
IP address 192.168.1.228
Netmask 255.255.255.0
Gateway 192.168.1.1
DNS 192.168.1.1
Wi-Fi network module not present
Settings
Unit ID (Banner)
DHCP 0
IP 192.168.1.228
Netmask 255.255.255.0
Gateway 192.168.1.1
Dns server 192.168.1.1
Extern IP/Host
Eth-type 5
Web page user
Web page pwd
Program mode 9
Control panel 0
Sip password XXXXXXXX
Sip contact
Auto connect 0
Audio quality 2
Audio dual-rx 1
Codec out gain 255
Codec inp gain 0
Codec inp HPF Hz 3
Codec inp preamp 1
COM0 baudrate 38400
COM0 data bits 8
COM0 stop bits 1
COM0 parity 0
COM0 Program mode 3 char timeout 2
Use USB Com Port as COM0 0
COM1 mode 0
COM1 baudrate 9600
COM1 data bits 8
COM1 stop bits 1
COM1 parity 0
COM1 rts/cts 0
COM1 terminator (hex) 00
Use USB Com Port as COM1 0
COM2 mode 0
COM2 baudrate 9600
COM2 data bits 8
COM2 stop bits 1
COM2 parity 0
COM2 terminator (hex) 00
Use USB Com Port as COM2 0
UDP cmd port 12000
UDP audio port 11000
SIP port 5000
Web server port 80
Telnet server port 23
Rx jitter buffer size 4
Rx jitter delay 3
Audio packet size (ms) 20
RTP tx mode 0
Debug level 0
Disable audio tones 0
Full duplex 0
PTT-off mute delay 0
IP Type-of-Service (dec) 0
Yaesu power-on/off 0
Elecraft advanced 0
Dynamic DNS check interval 10
Dynamic DNS host name 0
Own host name XXXXXXXX.ham-radio-op.net
Username XXXXXXXX
Password XXXXXXXX
Enable 0
Speed wpm [0/10-40] 0
Iambic 1
Paddle reverse 0
Weight [25-40] 30
Side tone hz [0,300-1500] 800
Side tone -db [50-0] 20
Lf delay ms [0-500] 0
Key delay ms [0-250] 0
PTT activated by Keyer 0
PTT tail delay ms [0-999] 0
Speed pot min wpm [5-99] 10
Speed pot max wpm [5-99] 40
IN0 mode 0
OUT0 mode 0
OUT0 mode 0
OUT1 mode 0
OUT1 mode 0
OUT2 mode 0
OUT2 mode 0
USB RTS as PTT 0
USB DTR as CW 0
Enable ping watchdog 0
IP address to ping
Ping interval (seconds) 300
Startup delay (seconds) 300
Failure count to reboot 3
1: Name (SSID)
1: Password (PSK)
2: Name (SSID)
2: Password (PSK)
3: Name (SSID)
3: Password (PSK)
4: Name (SSID)
4: Password (PSK)
5: Name (SSID)
5: Password (PSK)
6: Name (SSID)
6: Password (PSK)
7: Name (SSID)
7: Password (PSK)
8: Name (SSID)
8: Password (PSK)
Status
Name Value
Radio ON
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 1
SIP Out port 5000
SIP In port 5000
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5000
External Audio In port 11000
External Cmd In port 12000
Other party 0.0.0.0
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
Dynamic DNS status Error, code 4
Ping status (watchdog) Off
DNS status Error, failed to resolve remoterig.com!
Active profile: Default
PTT status: OFF
****************************************************************
Info
Name Value
Company Microbit
Product 1258
PID 0
Version 5
HW 6
Software 2.60
Bootloader 1.9
Compiler 4.6.2
Build Jun 18 2012 14:23:22
ROM/RAM 435604/56456
ETH-RAM 2944 (max 3kB!)
ResetSrc 0 [3]
Uptime 254
Serial number 4700
MAC address 00:1e:fd:01:88:fc
IP address 192.168.0.227
Netmask 255.255.255.0
Gateway 192.168.0.1
DNS 192.168.0.1
Wi-Fi network module not present
Settings
Unit ID (Banner) IC-2820
DHCP 0
IP 192.168.0.227
Netmask 255.255.255.0
Gateway 192.168.0.1
Dns server 192.168.0.1
Extern IP/Host
Eth-type 5
Web page user
Web page pwd
Program mode 9
Control panel 1
Sip password XXXXXXXX
Sip contact XXXXXXXX.ham-radio-op.net
Auto connect 1
Audio quality 2
Audio dual-rx 0
Codec out gain 255
Codec inp gain 18
Codec inp HPF Hz 3
Codec inp preamp 1
COM0 baudrate 38400
COM0 data bits 8
COM0 stop bits 1
COM0 parity 0
COM0 Program mode 3 char timeout 2
Use USB Com Port as COM0 0
COM1 mode 0
COM1 baudrate 9600
COM1 data bits 8
COM1 stop bits 1
COM1 parity 0
COM1 rts/cts 0
COM1 terminator (hex) 00
Use USB Com Port as COM1 0
COM2 mode 0
COM2 baudrate 9600
COM2 data bits 8
COM2 stop bits 1
COM2 parity 0
COM2 terminator (hex) 00
Use USB Com Port as COM2 0
UDP cmd port 12000
UDP audio port 11000
SIP port 5000
Web server port 80
Telnet server port 23
Rx jitter buffer size 16
Rx jitter delay 15
Audio packet size (ms) 20
RTP tx mode 0
Debug level 0
Disable audio tones 0
Full duplex 0
PTT-off mute delay 0
IP Type-of-Service (dec) 0
Yaesu power-on/off 0
Elecraft advanced 0
Dynamic DNS check interval 0
Dynamic DNS host name 0
Own host name
Username
Password
Enable 0
Speed wpm [0/10-40] 0
Iambic 1
Paddle reverse 0
Weight [25-40] 30
Side tone hz [0,300-1500] 800
Side tone -db [50-0] 20
Lf delay ms [0-500] 0
Key delay ms [0-250] 0
PTT activated by Keyer 0
PTT tail delay ms [0-999] 0
Speed pot min wpm [5-99] 10
Speed pot max wpm [5-99] 40
IN0 mode 0
OUT0 mode 0
OUT0 mode 0
OUT1 mode 0
OUT1 mode 0
OUT2 mode 0
OUT2 mode 0
USB RTS as PTT 0
USB DTR as CW 0
Enable ping watchdog 0
IP address to ping
Ping interval (seconds) 300
Startup delay (seconds) 300
Failure count to reboot 3
1: Name (SSID)
1: Password (PSK)
2: Name (SSID)
2: Password (PSK)
3: Name (SSID)
3: Password (PSK)
4: Name (SSID)
4: Password (PSK)
5: Name (SSID)
5: Password (PSK)
6: Name (SSID)
6: Password (PSK)
7: Name (SSID)
7: Password (PSK)
8: Name (SSID)
8: Password (PSK)
Status
Name Value
Control panel ON
Radio ON
Connection status Disconnected
SIP status Unknown(1)
Last SIP error SIP Error
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 5
Rx Jitter buffer size 16
Rx Jitter delay 15
Dual Rx 0
SIP Out port 5000
SIP In port 5000
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5000
External Audio In port 11000
External Cmd In port 12000
Other party 192.168.2.2
Input 0 High
Input 1 High
Input 2 High
Output 0 High
Output 1 Low
Output 2 Low
DNS status OK, XXXXXXXX.ham-radio-op.net = 192.168.2.2
Active profile: Default
PTT status: OFF