Messages

1

General discussion forum / Re: Controlling K9AY directions via I/O port is easy done

« on: 2016-02-02, 13:56:10 »

Granted, this version better. But I have to make for friend cheapest option. I used the web switch to another station for 4SQ.

2

General discussion forum / Re: Controlling K9AY directions via I/O port is easy done

« on: 2016-02-02, 12:00:20 »

Unfortunately, in the file does not open, you could not transfer the file again.
Thanks!

3

Configuration, RRC 1258 / Re: K3 problem

« on: 2015-12-16, 13:37:31 »

SM2O, thanks for help. I set in RRC-control mode 4 and i set auto connect. It`s ok. In RRC-radio stay mode k3 twin . I set virtual splitter (VSPE) for COM1 (RRC) and now i use together Win4K3suit and any logger.
Serge UR5MID

4

Configuration, RRC 1258 / K3 problem

« on: 2015-12-15, 09:42:59 »

I'm used K3/0 mini. Everything works fine. But I decided to try to use the remote control without the panel. Such problem: In the HamRadiDelux if I choose COM2 (on my PC COM4), then turn on the radio, I hear sound, but turns off after a few seconds.The program reports, do not read the data frequency. If I connect to COM1 (on my PC COM3), nothing happens at all. COM1 mode 7. What is the problem?
Serge UR5MID

5

Configuration, RRC 1258 / Re: K3/0 problem CAT

« on: 2013-09-08, 08:33:53 »

now ok

6

Configuration, RRC 1258 / Re: K3/0 problem CAT

« on: 2013-09-07, 21:59:32 »

I installed COM1 to mode 7. it`s work very well.
But i have new problem. After 15 minutes, the connect disappeared. The control panel shows the message "IP error." I do not know why. Installation did not change, except for COM1.

7

Configuration, RRC 1258 / Re: K3/0 problem CAT

« on: 2013-09-05, 22:46:00 »

I will try to install tomorrow.
But i want using COM1  for rotator.
COM0, COM1,COM 2 only for CAT???
it`s stangely

8

Configuration, RRC 1258 / K3/0 problem CAT

« on: 2013-09-05, 19:15:04 »

K3/0 working is well without computer. Any logger do not find com-ports. I tried via virtual port or to direct COM1.But no results.
PS: COM1 ( COM4)
COM2 ( COM7)

control panel serial number 2511
radio control serial number 2600
software 2.72

Serial settingsCOM1 mode    3
COM1 baudrate    1200
COM1 data bits    8
COM1 stop bits   1
COM1 parity   off
COM1 rts/cts    yes
COM1 terminator (hex)   
Use USB Com Port as COM1 yes   
    
COM2 mode    logical parallel with com0   

COM2 baudrate    9600
COM2 data bits    8
COM2 stop bits    1
COM2 parity    off
COM2 terminator (hex)   o
Use USB Com Port as COM2 no   
    
COM3 mode (USB-COMFSK)







Radio settings 14   
Sip password   
Sip contact   
Auto connect    No
Audio quality    2
Codec out gain   255
Codec inp gain   18
Codec inp HPF Hz    327
Codec inp preamp yes   
COM0 baudrate    9600
COM0 data bits    2
COM0 stop bits    off
COM0 parity   2
COM0 Program mode 3 char timeout   
Use USB Com Port as COM0   no   

9

Configuration, RRC 1258 / Re: K3 twin problem

« on: 2012-11-03, 00:34:29 »

I had already read the instructions about it.
but there is no connection at startup. I replaced COM0 parity : 0 to force 1 and all is ok. But in local net, next step-internet connection.

10

Configuration, RRC 1258 / K3 twin problem

« on: 2012-11-02, 22:41:24 »

I have K3/0 and RRC1258MkII (serial # 2600-radio, #2511-control) . I choose " K3 twin" in radio setting, but i dont have button "connect" in window "status". What is problems?
Firmware 2.62