Messages

1

General discussion forum / Re: K3 twin - power on - and more

« on: 2014-09-02, 02:34:32 »

ok - just to close this thread.

* Using the Heil headset ( Proset plus ) I think with the HC5 element does not require / does not work with JMP1 installed
* When I used the footswitch connected to the HEIL adaptor everything worked (after I removed JMP1)
* I now know what  "RTP tx mode ( normal/continuous )" does:  audio is muted until PTT is pressed and  PTT must be on the control side, does not work pressing "XMIT" on either of the K3's as in the "normal" mode - RRC will not transmit audio unless control unit is keyed through the MIC connector.


I'm a big VOX fan in contests, first time actually that I connect a foot switch - so this might be something I would consider - but I agree with the "security" issue.

so now everything working fine !

73, Benni TF3CY

2

General discussion forum / Re: K3 twin - power on - and more

« on: 2014-08-31, 01:36:54 »

one more thing if anyone knows

I have a Heil proset plus that I use with the normal adaptor to my K3 - it does not work.

* I removed jumper 1 before  I plugged the MIC in
* I have confirmed it works with my K3
* I use a Kenwood MIC that I have and it works perfectly directly connected to the RRC
* no audio - even if I manually PTT with "XMIT" button on K3
* no vox (ofc. if no audio)
* using the RED adaptor from HEIL.

any thoughts ?

73, Benni TF3CY

3

General discussion forum / Re: K3 twin - power on - and more

« on: 2014-08-30, 22:46:47 »

well, found the solution!

double checked my Cisco router, using Wireshark I could see I was connecting - but never getting any responses from the remote unit.

After looking at the Radio Settings in the control unit I saw this:

I double clicked the "SIP contact" IP address:


I noticed that there is a space behind the IP address - so this is a parser issue in the RRC  - probably in the remote SIP part -as I could see the control unit try to connect - but I never saw any connections coming back.

When I remove the space behind the IP address - everything goes back to normal.
This has been replicated on the local LAN also (I have two RRC's)

Not being a software bug per se - it's something that can cause issues as IP addresses are often copied and pasted and this space is often copied with them. With proper input parsing this "issue" could be totally avoided.

73, Benni TF3CY

4

General discussion forum / Re: K3 twin - power on - and more

« on: 2014-08-28, 15:34:26 »

ok - let's not worry to much

I'm trying to establish a baseline how things should be - as I cant test this over a LAN - so there is the internet and the external router at the remote site that I have not yet looked at.

But I have tried few cables etc..  the K3 does not enter this TERM mode automatically - but with the supplied cable, the control RRC does detect that the radio is on - but I'm still always disconnected in the connection status. Trying to figure out how this hangs together - perhaps the RRC does not put the K3 in TERM until it's connected - or perhaps it does not connect until it detects the control radio... this would help me figure out where to go next.

When I get control over the whole thing - I will post my findings or further answers !

thanks

- Benni TF3CY

5

General discussion forum / Re: K3 twin - power on - and more

« on: 2014-08-28, 11:56:38 »

ok  thanks for the input

I have now tried 9600/38400 - no difference.

Radio is connected to the back panel COM port with the cable supplied in the kit.

and there is a big assumption that the AUX/ACC cable is connected on the remote site. This was apparently working before.

- RRC states "radio ON" on the control side when I turn the K3 on
- K3 does not enter terminal mode when turned on
- I have turned off all keying via serial
- I have multiple screenshots showing / config import from another RRC that has been used - so I have something to compare.

and to note - haha..just figured out this term mode
- I can't find it anywhere in the documentation
- I have been able to turn it on with serial commands
- and the K3 has to be powered on - and then you long-hold menu - I was sure you had to power the K3 ON into TERM mode. (", just hold down the menu button longer until it turns on")

Problem is that I don't have physical access to the remote K3/RRC - only web access to the RRC
but my friend that owns the remote station will be there in few days - so I will debug further when I can rule more things out.

73, Benni TF3CY

6

General discussion forum / K3 twin - power on - and more

« on: 2014-08-28, 01:45:09 »

Hi there

I just got a RRC-1258MkIIs and I'm connecting to a K3 in remote mode with a full blown K3/100 as the control unit.

I have been reading as much as I can - I have been unable to turn on the remote K3.

- I have access to the remote RRC - shows radio off / disconnected state. Other party shows my IP in status.

- Do I have to do anything to my control K3- terminal mode ?  - if so - how do I turn it on ? (google is not helping me!)
- Can I issue a "turn on" using the telnet server on the remote site ?

and further - is there any documentation on the telnet interface of the RRC ? (being a Cisco network engineer I like console access!)

73, Benni TF3CY