Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - EA4MY

Pages: [1] 2
1
General discussion forum / Re: DDNS server unreachable
« on: 2023-05-26, 12:39:39 »
It's working again. Thank you for fixing it !
73
Antonio, Ea4MY

2
General discussion forum / Re: DDNS server unreachable
« on: 2023-05-25, 20:56:36 »
Same here since two days ago.
Any info please?
73
Antonio

3
I've been working mainly CW for several years now with spring return iambic paddles (a Bencher and a Vibroplex) with no problem. A few months ago I started working with two iambic paddles with magnetic return (a Begali and a UR5CDX) and, to my surprise, from time to time, the manipulation gets blocked, that is, even though one paddle is activated (dit or dat), no manipulation occurs, and only after releasing of the paddle, again everything works again. This happens only with the two magnetic return paddles, but not with the spring return paddles. I am wondering if this has happened to anyone else and if this is a known thing and what is the influence that the magnetic return of a paddle can have on the electronic key function of the RRC-1258 MkII. The only solution that I have found for the moment is to put an intermediate electronic keyer between the paddle and the Control-RRC and use the I/O connector IN0-1 mode as an external keyer.

4
Hi
I started two months ago a thread in the General Discusion Forum of the RRC1258 because I'm suffering quite frecuently a lot of troubles to access remotely to the webserver of the RRC Radio. The answer was that the problem seems to be originated by the overload caused by robots, so the only solution should be to setup a VPN- not an easy thing at least for me.  Now, I'm thinking about to buy a Webswitch 1216H and a Rotator Control Unit 1216L  which is based on the permanent remote access to its webserver, but in view of the frecuent problems I'm having to access remotely to the webserver of the RRC radio I have a lot of doubts if this can (or will) happen as well with the Webswitch server . Is my guessing correct?
Many thanks in advance
73
Antonio, EA4MY

5
I forgot a question: does it helps in any way if I change the web access password to a more complex and large, or this has nothing to do with the access of the attacks ?
Many thanks
73
Antonio, EA4MY

6
OK Mike, you mean instead of a L2L VPN tunnel a client - Server tunnel. Well OK, but I nerver use phone or tablet to make radio. I do radio only from the TS480 detachable front panel at the control QTH. Any way many thanks. I'll see if I can do something with the help of some friend, if not, to withstand the attacks while they last... :-\  or maybe to change the actual web port to see if the attacks are not so often.
73

Antonio, EA4MY

7
OK Mike, I see. Just to confirm: the VPN tunnel you suggest to avoid attacks has to be stablished between the routers on both ends radio<->control. Isn't it?.
Many thanks
73
Antonio, EA4MY

8
I understand the VPN tunnel should be setted up between the routers on both ends ?. I'm not an expert in this kind of things. If so, I'll  try to see if I can do something. And, yes, I access to the RRC-radio web site every time I want to make radio because I'm using the output OUT0 on the RRC-radio to switch on-off the TS480 PS, and the PC I'm using at my home on the control side is not premanently connected. In any case I'm intrigued why this started to happen two weeks ago and happens so frecuently (every one or two days). Is it normal attacks to happen so frecuently?.  After all this web server is one more among the hundred of millions in the world... :(  >:(
73
Antonio, EA4MY

9
Mike, as far as I understand from your comments there is nothing we can do to avoid these overload attacks from robots, and how long do the attack last is unknown.  According with this a hard reset does not help because after the reset, the attack is still on and the web server hangs again. Is this what you mean?. If this is the case, this situation should be quite common to many of us. I do not know if many people report this kind of issues.
73
Antonio, EA4MY

10
Mitch, I'm using from the very beginning (following your indications years ago) a different port to the 80.
Mike, as I can't reset remotely with the web interface, what I have made every time this happens is a localy hard reset (a local preson on the RRC-radio site swtich off the the RRC' PS), but, as I commented previously, with no results, as the web page doesn't come up, and I have to wait an undefined number of hours until the web page come up again. For instance, right now is up again. I can send the settings .bin file to you  if this can help in any way.
73´
Antonio, EA4MY

11
Hi
I made the upgrade to v2.95 on both ends but this afternoon once again happened the same. I have only a parcial access to web page of the RRC-radio (same as the jpg picture I sent before). This time does not appear any "saved error message". However what I see is that I have communication between both ends as I can switch on and off the TS480 and I receive signals and I can transmit. The problem seems to be with the web server, so I can not switch on and off remotely the Power Supply using the web interface (and, as well, I don't have remote access to the left side menu). I will thank any other hint.
73'
Antonio, EA4MY

12
I have v2.84, and I just saw on the web that in my case I have to upgrade both ends.
73

Antonio, EA4MY

13
Hi Mike
Many thanks for your suggestion.  I should do that on both ends, I mean, on RRC radio and control, isn't it?
73
Antonio, EA4MY

14
Hello all
I'm running a TS480 since a few years ago. Everything worked fine until aprox two weeks ago. Since then the connection of the RRC radio fails every few days. I have made not any changes on the configuration, nor changed any hardware (router, etc). No changes here at all. No storms here or anything else that could damage the RRC. When, from inside the RRC radio LAN, I type in my PC the RRC IP what I get is what can be seen in the attached .jpg picture, that is, only the "structure" of the web site but whitout the left side menu. There appear a "Saved error message": Data abort at 0x0004a998, called by 0x0004a964. I don't know what that means. Under these conditions I guess I can not download any BIN file. I have made a hard reset of the RRC but without results. This happens every one or two days.  Looks like a problem into the RRG, but I don't know. I will thank any hint to solve the situation. Right now I'm down.
Many thanks in advance
73
Antonio, EA4MY

15
Everything is working back again.
Many thanks for the support.
Best 73

Antonio, EA4MY

Pages: [1] 2