Messages

1

Hardware, Cabling, Installations / Re: K3 Twins, No Mic Audio...

« on: 2016-05-23, 15:23:40 »

i followed this closely, made sure settings were as above.. and set my K3/0 mini to Fp.h while totally unplugged from control RRC..... then made sure the remote K3s was set to Rp.h, reconnected, and still no PTT or VOX action with my setup. When the mini is unplugged from the RRC. the PTT foot pedal does key the mini (red light on..) while plugged into mini front pedal... hook up RRC control.. connected to RRC radio and doesn't work. As noted bias seems to have no effect... Also, I unplugged the mic connection on the control RRC, plugged in yeas mic with RJ45 plug... no PTT and no VOX effect-- ditto when plugging it into the RRC radio side .

Doing all this in the same shack connected through router so there are not internet problems.

Comments -- the elecraft instruction say to put CODEC ATTENTUATION to yes! audio much stronger when set to NO
and yes I have RTP continuous and full duplex ON... (if off I have no receive audio in mini)

Is there a special thing about the mini concerning recognizing the mic plugged in the front?

I hope Brandon reads these and  can weigh in
bob W5RF

2

Hardware, Cabling, Installations / Re: K3 Twins, No Mic Audio...

« on: 2016-05-23, 05:35:08 »

count me as number three! I am hoping this thread will get me going on SSB with my K3/0 mini to K3s ... It always confused me that I was changing to the rear plugs on the K3s, via the K3/0 mini remotely, yet I was using the front plugs on the mini for my headset and mic.
W5RF

3

Configuration, Webswitch 1216H / Re: Accessing 1216h

« on: 2015-09-08, 02:15:11 »

I had the same question... not getting into it. My RRC is working well through the static IP and I have port forwarded the 192.168.1.142 which is what I have assigned the web switch.. got your notes, will re review them

bobf

4

Configuration, Webswitch 1216H / Re: Webswitch 1216H: Device disconnected

« on: 2015-09-08, 02:00:16 »

I set up my webswitch with microbit, and usb cable and it works fine; on the loacl network, it works fine, but now that I am 100 miles away, trying to access it with http/// cannot get in. I have a static i.p so I tried http://[staticip:81]/relaycontrol/off/all and nothing happens. I DID do port forwarding of my IP for the web switch 192.168.1.142 for the switch.... suggestions?
bobf W5RF

5

Configuration, RRC 1258 / Re: How to configure Remoterig

« on: 2015-05-17, 23:10:25 »

For me, a static IP aat the radio end and a 300 foot cat 6 solved all my problems. I could never figure out how to do port forwarding between to wireless routers with the radio shack router operating as a universal repeater. now with one router, a long cat 6 solved my problems. need to bury it now. working on the rr micro now trying to get it to turn on my ft 857 which I have set up to work with the front panel off and at remote site, or in car with a hot spot. cool..

bobf

6

Configuration of Routers, Firewalls, etc / Re: Router config

« on: 2015-03-20, 01:37:10 »

thanks!

7

Configuration of Routers, Firewalls, etc / Re: Router config

« on: 2015-03-18, 10:26:55 »

Mitch - could you drop me the same quick setup sheet? thanks and 73s.. bob W5RF