Messages

1

General discussion forum / Yaesu FTdx101 via RRC-1258 MkII

« on: 2021-05-25, 17:11:31 »

Hello group,

I see in the manuals for the Yaesu SCU-LAN10 that they do not support FT8 or CW.
So what are the options for proper remote use of that rig?

Anyone tried to use the RRC units?

Best 73, Per-Tore / LA7NO

2

Hardware, Cabling, Installations / Re: RRC cabled or WiFi

« on: 2021-01-18, 15:31:45 »

Thanks, Mike.

P-T

3

Hardware, Cabling, Installations / Re: RRC cabled or WiFi

« on: 2021-01-16, 22:08:38 »

Thanks, Mike.

On the Info page of the RRC I get:

Serial number   9934
MAC address   00:23:a7:c7:51:4b
IP address   192.168.38.110
Netmask   255.255.255.0
Gateway   192.168.38.1
DNS   192.168.38.1
Wi-Fi network   Nabo2

Will this MAC always the of the cables connector?
For this particular case, the RRC is not cabled, so this interface is not active.

I can also see that a WiFi network is indicated.

But in the general case, were both WiFi and cable are connected, it could be that either of them are not good for Internet access. If I can connect to the RRC from the outside, then I can not know what interface it is using?

In case it is cabled, it could still be that there is no Internet connection, so it tries the WiFi.

Will it automatically try the other connection if the active one stops working?
Or will a reset be required?

P-T

4

Hardware, Cabling, Installations / RRC cabled or WiFi

« on: 2021-01-15, 23:32:52 »

Hello group,,

When I connect to a remote RRC Radio, is it possible to see if it is connected to its router via cable or via WiFi?

73,

Per-Tore / LA7NO

5

General discussion forum / Re: Codan NGT to be used with RRC?

« on: 2020-12-29, 18:32:49 »

Hi,

I have a couple of NGT radios.
Any news on this topic?

73,

Per-Tore / LA7NO

6

Hårdvara, Kablage, Installationer / Re: Ferdig lagd kabel for TS-480 control

« on: 2020-12-28, 21:21:41 »

Hei Alf,

Av forskjellige grunner, så la jeg først idag merke til ditt svar på mitt spørsmål på Remote Rig forumet.

Lurte på om du fortsatt har anledning til å lage en slik kabel med RJ-45 i ene enden og 3,5 mm stereo plug i den andre? Ca 40-50 cm lang, slik at jeg får plass til ferritter.

Har brukt Remoterig RRC -1258 MkII i mange år. Har brukt de med både Elecraft K3, Kenwood TS-480SAT og ICom IC-7100. Har fungert meget bra.

Hvordan er din erfaring med dem?

Beste 73,

Per-Tore / LA7NO

7

Hårdvara, Kablage, Installationer / Ferdig lagd kabel for TS-480 control

« on: 2019-10-26, 12:16:37 »

Hei,

Vet noen om der finnes ferdig laget kabel for kopling mellom RRC-1258 MkII og lydkortet?
Lydkortet har vanlige 3mm stereo jack kontakter.

Altså, en plugg til AUX/MIC pinne 3 (signal) og 4 (jord), samt en til SP.
Det er den som går til AUX/MIC (RJ45) som er problemet.
Den andre er standard stereo kabel.

Klarer ikke å lage dette selv, grunnet artrose i fingrene.

73,

Per-Tore / LA7NO

8

General discussion forum / Re: Cant browse to remote radio

« on: 2018-12-18, 15:08:16 »

Hi Mitch,

and thanks for your feedback. I totally agree.
Next month I will go to where the radio is located.
Hopefully a local connection can help putting light to the problem.

BTW, it is "Per-Tore". ;-)

P-T

9

General discussion forum / Re: Cant browse to remote radio

« on: 2018-12-18, 09:23:37 »

Hi Mitch,

I did change the web port to 81, and added that after the colon.
But no contact.

P-T

10

General discussion forum / Cant browse to remote radio

« on: 2018-12-18, 01:20:05 »

Hi,

I am in Germany and the radio is in Norway.
I am using Windows 10 and Firefox.

I can use the radio in the usual fashion via the the two Remoterig units.
Everything works the way it should.

Now I need to reconfigure some settings on the radio side. So I try to connect to its Remoterig unit via the browser using the address given in control unit menu at "Sip contact(Radio RRC IP/hostname)", but get no response. However, both ping and tracert to this address gives the expected result.

What can the reason be that I am not able to get to the webpage of the Remoterig unit?

Best 73,

Per-Tore
DL/LA7NO

11

Hardware, Cabling, Installations / Re: Elecraft K3 + K3/0-mini + Expert 1K-FA

« on: 2017-02-27, 11:37:34 »

Hi,

I use the attached cable from K3 ACC to 1K-FA CAT. It transfers only th band-data. So, it does not interfere with RS-232.
If I use an Y-cable, the RS-232 data can betransferred on the other free lines.

Or?

P-T

12

Hardware, Cabling, Installations / Re: Elecraft K3 + K3/0-mini + Expert 1K-FA

« on: 2017-02-27, 10:57:12 »

Would an Y-cable connected to the K3 do the trick?
Then one connctor can got to Remoterig and the other to 1K-FA CAT.

P-T

13

Hardware, Cabling, Installations / Re: K3 remote

« on: 2017-02-27, 10:48:30 »

Hi Mike,

and thanks for your comments.

It is a K3/0-mini.
The mic is connected to the std. mic connector on the front.

What else can I check?

P-T

14

Hardware, Cabling, Installations / K3 remote

« on: 2017-02-27, 10:26:03 »

Hello,

The last few days we have been working on setting up K3 + Remoterig + K3/0-mini to communicate over Internet using wirelss 4G routers. All seems to work just fine on receive and CW transmit.
However, we have not managed to get it to work using the mic.

I have been using an old Kenwood dynamic mic.
The K3 is configured with mic set to "rP.L" (no bias)
The K3/0 is set to "FP.H" (also no bias).

Also tried with a Heil headset.
Tried this with K3 set to both "rP.H bIAS" and "rP.H" (no bias)
Also tried with K3/0 set to "FP.H bIAS".

Nothing worked, even with mic gain set to max.
Now I start to wonder if there can be something wrong with the Remoterig configuration.

Hope someone can help.

Regards,

Per-Tore
LA7NO

15

General discussion forum / Re: RemoteRig over Cellular Network

« on: 2017-02-21, 20:26:47 »

I have just tested connecting the RRC-1258 Radio to a ZTE MF90+ 4G LTE router.

Used a Telenor/TalkMore SIM and was automatically given an IP-address in the public range. No extra cost. Only had to configure port-forwarding and set the APN to 'internet.public'.

Works very well.

73,

Per-Tore
LA7NO