1
General discussion forum / Re: IC7100 issue
« on: 2019-11-14, 07:00:05 »
On the rrc attached to the radio
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
General discussion forum / Re: IC7100 issue
« on: 2019-11-13, 21:53:51 »
In my case the problem was an hardware fail. A logic gate burned together a smd coil.
3
General discussion forum / Re: IC7100 issue
« on: 2018-09-29, 19:45:06 »
I did the check of the red cable two weeks ago and on the same lan.
The result is always the same.
I'll.do it again.
The result is always the same.
I'll.do it again.
4
General discussion forum / Re: IC7100 issue
« on: 2018-09-29, 11:15:48 »I have sent you instructions via email
73 de mike
The issue related to the DDNS was solved.
Not the issue of the topic.
The CP and R still doesn't work.
ANY IDEA?
This is again the debug from CP
New UDP CmdTxPort=13002
rtp enable [79.53.234.61/13001 79.53.234.61/13001]
queueExtIOManually, In1=8 In2=32 In0=4
sendExtInputs, In1=255 In2=255 In0=4
CP-> Sending 8V: 0 Mute spk: 0
CP-> audioQuality=10
duplex: New Audiocoding 110 (24 KHz)
Got Radio Info, Len 5, data: '8VOff'
CP-> Panel '8V off' from radio
CP-> Radio/Panel OFF (0)
rtp disable
and from the R
duplex: New Audiocoding 110 (24 KHz)
duplex: New Audiocoding 110 (24 KHz)
New UDP CmdTxPort=13002
SIP Saved Call-ID '19011147@192.168.1.30'(2)
duplex: New Audiocoding 110 (24 KHz)
duplex: New Audiocoding 110 (24 KHz)
duplex: New Audiocoding 110 (24 KHz)
New UDP CmdTxPort=13002
SIP Saved Call-ID '19011147@192.168.1.30'(2)
R-> Radio ON requested (2)
rtp enable [79.12.223.80/13001 79.12.223.80/13001]
R-> Connection established, radio ON, audioQuality=10
duplex: New Audiocoding 110 (24 KHz)
queueExtIOManually, In1=8 In2=32 In0=4
sendExtInputs, In1=8 In2=32 In0=4
controlUDPMsg, Out1=255 Out2=255 Out0=4
Got Radio Info, Len 5, data: '8VOff'
R-> Radio '8V off' from panel
ptt off (delayed)
R-> Sending '8V is off'
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
ptt off (delayed)
rtp disable
>>>Unknown ICMP-package received, type 192 code 168
ptt off (delayed)
5
General discussion forum / Re: IC7100 issue
« on: 2018-09-23, 17:08:21 »
Finally I checked.
The sticker inside reported snr: 8565
Exactly how I had previously in the ddns menu.
How can I solve it?
Can be a part of the issue?
The sticker inside reported snr: 8565
Exactly how I had previously in the ddns menu.
How can I solve it?
Can be a part of the issue?
6
General discussion forum / Re: IC7100 issue
« on: 2018-09-16, 22:48:06 »
a little other anomalies.
I'm pretty sure that the serial number of the RRC was 8565.
I have stored the value of the ddns and it was rrc1258-8565 and this generated a xxxxxx.ddns.remotertig.com
Now the serial number is 8566 and I can found it in the ddn menu.
I start checking often the IP values and I found that it fluctuates pointing to another RRC.. What I think is that the serial number belongs to another person and I and him are pushing IP overlapping the values in time.
Exactly is mr JJ8LNX found it in the info screen. I'll contact him for a confirmation.
I'm pretty sure that the serial number of the RRC was 8565.
I have stored the value of the ddns and it was rrc1258-8565 and this generated a xxxxxx.ddns.remotertig.com
Now the serial number is 8566 and I can found it in the ddn menu.
I start checking often the IP values and I found that it fluctuates pointing to another RRC.. What I think is that the serial number belongs to another person and I and him are pushing IP overlapping the values in time.
Exactly is mr JJ8LNX found it in the info screen. I'll contact him for a confirmation.
7
General discussion forum / Re: IC7100 issue
« on: 2018-09-16, 19:06:22 »
Ok.
Reset every single component (also the IC7100)
Connected in the same intranet and the result is exactly the same.
Checked the wire connection and the electric continuity: no problem
Cycle several time and in different order all the components.
So definitely not a communication due to the router.
The radio is working perfectly attached the panel.
I need some hint please.
Reset every single component (also the IC7100)
Connected in the same intranet and the result is exactly the same.
Checked the wire connection and the electric continuity: no problem
Cycle several time and in different order all the components.
So definitely not a communication due to the router.
The radio is working perfectly attached the panel.
I need some hint please.
8
General discussion forum / Re: IC7100 issue
« on: 2018-09-12, 15:19:23 »Just a question: Have you also rebooted power to the body of your IC7100?Before the RRC and the radio had the same power source, but after some trial in this issue I splitted in two separated source and cycled both several way.
I've had several occasions where the IC7100 body iteself had "crashed" and needed to be dis-/reconnected to PSU.
73
Paul
The Body IC7100 has also been tested directly with its front panel and was good.
9
General discussion forum / Re: IC7100 issue
« on: 2018-09-12, 15:17:34 »Still I would test all on the same table without internet and routers involved. Also check the red straps with an ohm meter they may be broken inside the red plasticOk, I can do it later in the week. Physical damage of straps are not the best candidate because the devices were not moved, but I'll check it.
/mike
10
General discussion forum / Re: IC7100 issue
« on: 2018-09-12, 08:23:13 »If it still not working with brand new RRC you know that's it not a Remoterig issue
/mike
Brand new power supply as suggested the units are the same.
11
General discussion forum / Re: IC7100 issue
« on: 2018-09-11, 20:34:42 »
I can't factory reset the device. Also after 20 seconds most of data are still there... how can do it?
12
General discussion forum / Re: IC7100 issue
« on: 2018-09-11, 20:17:06 »
Swapped both with brand new ones. No changes.
I have swapped several routers (i have a big amount) no change. Anyway to be sure I put the RRC in DMZ and checked the ALG SIP that is deactivated.
I'll try to factory reset the devices.
I have swapped several routers (i have a big amount) no change. Anyway to be sure I put the RRC in DMZ and checked the ALG SIP that is deactivated.
I'll try to factory reset the devices.
13
General discussion forum / Re: IC7100 issue
« on: 2018-09-10, 22:14:31 »
No why?
Here both the status exactly after the connection trial
CP after half second
Connection status OK
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status OK(45)
CP after couple of seconds
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
RCC after half second
Connection status OK
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status OK(42)
RCC after couple of seconds
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
I rebooted all the elements on the line (routers + devices + radio) several times.
Here both the status exactly after the connection trial
CP after half second
Connection status OK
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status OK(45)
CP after couple of seconds
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
RCC after half second
Connection status OK
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status OK(42)
RCC after couple of seconds
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
I rebooted all the elements on the line (routers + devices + radio) several times.
14
General discussion forum / Re: IC7100 issue
« on: 2018-09-10, 10:16:53 »
Hi Mike, my concern is exactly that nothing is changed also in the connection part.
Or better several modification have been done in these two years without affecting nothing, but non recent.
I mean't that the system was very relialable until now.
Now I'm trying to understand how to recover from this and to recover from this I need to understand which is the problem.
All the networking stuff are correct, because the two devices communicates at low level.
The error is in the SIP communication itself.
I'll post the status windows after trying to switch on.
Or better several modification have been done in these two years without affecting nothing, but non recent.
I mean't that the system was very relialable until now.
Now I'm trying to understand how to recover from this and to recover from this I need to understand which is the problem.
All the networking stuff are correct, because the two devices communicates at low level.
The error is in the SIP communication itself.
I'll post the status windows after trying to switch on.
I think the problem is that you are making things way too complicated. Let's have you simplify things a bit......
What is needed is the status page just after a connect is attempted. Only copy these lines for each RRC:
Connection status
SIP status
Last SIP error
RTP/UDP audio status
UDP cmd status
This should be all that is needed.
Now, on to your problem: if a system works for two years and stops working, there is a problem somewhere in the
environment and not the RRC's. No telnet listing will ever help you solve that problem.
Examples of things you need to look at:
- wiring that became broken or loose
- a switch or router that went bad
- your ISP switched to IPv6
For the last part, look at your router's status page to see what is there. You can compare what IP address your RRC says
it is using with what you see on http://www.whatsmyip.org/ to see if it is the same or different. I have seen a couple more
OM's in Italy have these problems because their IP moved them to IPv6.
73,
Mitch DJ0QN / K7DX
15
General discussion forum / Re: IC7100 issue
« on: 2018-09-08, 10:09:32 »
The status page output was already posted after you request (3rd post of the thread here: http://www.remoterig.com/forum/index.php?topic=6064.msg28360#msg28360 )
If you meant another status page please tell me.
If you meant another status page please tell me.