Messages

1

General discussion forum / control unit not showing as control

« on: 2024-02-12, 06:48:11 »

I bought some used units.  The tags on them said serial number 9937 - radio unit and the other said 9940 control unit but when I hook up they both say they are a radio unit and both show serial 9937 although they do have different mac addresses
The control unit ( yes it has the cw knob, has a mac of :00:1E:FD:01:9D:71
The actual radio unit (no cw knob) has a mac of :00:23:a7:4f:ab:2d

How or can they be corrected?  I have tried reset several times but they still both come up 9937 a radio unit .

WD0AJG

2

General discussion forum / Re: Using FT8 and JT65 over remoterig with IC7100

« on: 2021-08-30, 04:34:32 »

Thanks, will do a change tomorrow or next day and do some more testing.

WD0AJG

3

General discussion forum / Re: Using FT8 and JT65 over remoterig with IC7100

« on: 2021-08-29, 06:22:26 »

I have tried several times and the signallink works fine in the radio back mic jack - but in the controlhead mic input I can't get any TX - I do get RCV and good decodes.  It will go into TX but no power out?  I am sure it is a setting but so far I have not found out the correct combination. 
I have the CI-V link on the radio side COM2- and then COM2 on the control unit to the computer - no problem controllng the radio with HRD.  I also can plug the signalink into the back of the radio and get tx and rcv fine, but when I move the signalink RJ45 t the control head mic jack it does everything but TX. since it work in the radio I figure i have the jumper correct in the signalink.  There is no info that the jack in the radio is different than the control? What am I missing?

WD0AJG

4

Configuration, RRC 1258 / Re: radio unit reset with bad serial

« on: 2020-10-09, 16:04:24 »

ok, if i was to try that "command" ?  I had to put in the port that I have that unit on and tried that input and got this in return

CRC mismatch, PID not changed!

WD0AJG

5

Configuration, RRC 1258 / Re: radio unit reset with bad serial

« on: 2020-10-09, 15:41:04 »

Jan, not sure I understand your post but if you wanted this:

Name   Value
Company   Microbit
Product   1258
PID   4294967295
Version   7
HW   8
Software   2.95
Bootloader   1.14
Compiler   4.6.2
Build   May 4 2019 08:32:26
ROM/RAM   488400/44304
ETH-RAM   3000 (max 3kB)
USB-RAM   16376 (max 16kB)
Battery-RAM   4
ResetSrc   0 [3]
Last WD Reset   9
Uptime   0 Days, 10 Hours, 35 Mins, 48 Secs
    
Serial number   117835012
MAC address   00:1e:fd:07:7b:a4
IP address   192.168.10.67
Netmask   255.255.255.0
Gateway   192.168.10.1
DNS   192.168.10.1
Wi-Fi network   module not present
Webserver   1
------------------------------------------------------
also it has reverted to default ip once when it reset. 
WD0AJG

6

Configuration, RRC 1258 / Re: radio unit reset with bad serial

« on: 2020-10-07, 04:47:46 »

now I need to add, out of chance I tried to link back to the old name and it now links that I have it hooked to router with correct IP but going to the unit it still shows the wrong info:

This is what it shows on the radio unit via webaccess (knew the ip address and I had moved the webpage to a diff port) . 

new stillwater+ NOT REGISTERING
r46gud28.ddns.remoterig.com
rrc1258-117835012
pw= grru7jaw

the old name was :
vtd8kgu1.ddns.remoterig.com and I can link to that old name?

7

Configuration, RRC 1258 / radio unit reset with bad serial

« on: 2020-10-07, 03:45:10 »

I had my units working.  was connected and did a disconnect then I can't connect.  At that site I also have a teamviewer computer and checked the router and the radio unit was not connecting to the network.   I had it hooked up to the USB and it came up with a erronous huge serial number (117835012).  via setup but it does not show mac .  So we did a full reset push of the reset button for 20+ seconds and it did come up and had base IP address of 192.168.0.228 and via the microbit setup I was able to get it back to the 192.168.10.67 needed to access the router but it still has the false serial in the net info box I get all the rigt stuff for linking to the router but below I get:
Device connected!
FW/HW version suddessfully retrieved
SW version succesfully retrieved
117835012!=11783501

it also now has a new set of addresses for the ddns settings and I can not change them back to what I had before and with the huge serial it is not logging in
username shows rrc1258-117835012 
when I go search for it it does not show up via it's own host name that is now different from previous 
the old original serial should have been 13889.

How to I get it reset to access?