Messages

1

General discussion forum / Re: Switching between PC-Client and TS-480 Control Head?

« on: 2010-11-30, 11:21:58 »

Mitch

what would be the setup on the RRC for this

I have the same setup Id like to try

2

General discussion forum / Re: newcomer - connectivity issues

« on: 2010-10-12, 07:37:37 »

latest 2.21
and yes basic out of the box config

May I ask what you did to set default settings?

checked the config with the usb and config mgr

set the network settings to my home network

that was it

nothing more

3

General discussion forum / Re: newcomer - connectivity issues

« on: 2010-10-12, 07:36:06 »

The web browser being slow may indicate that something is overloading the CPU, which may cause the connection to fail too. Do you have USB connected or disconnected? Is the web browser slow even if you disconnect everything but power and network?

its slow with only power and network yes

4

General discussion forum / Re: newcomer - connectivity issues

« on: 2010-10-11, 20:26:56 »

Sorry to hear about your ongoing problems!

One possible reason for resetting while browsing to it could be corrupt settings. Have you tried resetting the settings to their default values? Which firmware version are you using?

latest 2.21

and yes basic out of the box config

5

General discussion forum / Re: newcomer - connectivity issues

« on: 2010-10-11, 20:25:18 »

ok i dont know how I managed to get debug mode on

thats off now!

anyway still no connection between them

they are sitting on the same switch on the bench and cannot connect

all v odd

the web browser on the radio unit is extremely slow

Im down to basics ...... any poss that the units are defective?

Ill post the configs later but not really a lot in them

Ive even reloaded the firmware

?

ideas ?

6

General discussion forum / Re: newcomer - connectivity issues

« on: 2010-10-11, 09:11:26 »

is there any reason the control box would continually reboot while I am trying to browse its config using the web front end???

7

General discussion forum / Re: newcomer - connectivity issues

« on: 2010-10-11, 08:56:04 »

hmm i have no yellow led at the aux

I guess its not getting a connection for audio

8

General discussion forum / Re: newcomer - connectivity issues

« on: 2010-10-11, 08:44:34 »

yup did that ... I had got as far as creating a link but no audio flows over it

9

General discussion forum / newcomer - connectivity issues

« on: 2010-10-11, 08:04:25 »

HI all

I got a set of remote control boxes and am having real issues getting these going !

having realised my mistake with the pc client sw I am now back to the two box solution

I intend to use a 480 or 706 as a remote panel config but thought Id first test the box on the network as standalone

Ive configured the two box IPs for my internal network and they connect ok but I cannot seem to get audio across the link

Ive tried all sorts ... first as transparent - as a Icom CIV even as an ICR2500

I am only trying to send audio across the network just now from an AOR5000

no control data etc

not sure what could be the issue

I assume I stick audio on the radio SP socket and with two connected boxed hear the audio in the control SP port

no jumpers etc are in just now

can anyone guide me??

no lights on the front

network is connected and shows in the status ok as the partner

?

what am I doing wrong!

rgds

Simon ZL4PLM

10

General discussion forum / Re: PC client install issues - win7 64bit

« on: 2010-10-10, 11:17:49 »

ohh i see this is yet another box got it now

the pc cannot connect directly

ahhhh

ok back to plan a!

11

General discussion forum / Re: PC client install issues - win7 64bit

« on: 2010-10-10, 08:47:52 »

HI Mike

yes it fixed the install issue

but I get a "soundcard missing - please check cables error"

is this a config issue or software?

Simon ZL4PLM

12

General discussion forum / PC client install issues - win7 64bit

« on: 2010-10-08, 13:30:36 »

All,

I am having terrible issues with the latest pc client

RRC-Client-64Bit_1.0.10.exe

first the install fails

missing msvcr100.dll

found that and installed it onto the windows system folder

then I get an error message and crash

error. system.BadImageFormatException: An attempt was made to load a programme with an incorrect format.
at NativeMethods.Mblogger_enter string
at Microbit.gui.main
at Microbit.Programme.Main

I have to disable RRC.exe in the service under task manager to get it closed

please advise if anyone else sees this!

rgds

Simon ZL4PLM