Messages

1

General discussion forum / Re: Firmware 2.76 and IC-7100

« on: 2014-02-03, 20:25:51 »

Hallo Jan,

i have downgreat to 2.76 and the Problem is back.
After 3 mins uptime the box restart. The uptime Counter beginns new.

73
Oliver

2

General discussion forum / Re: Firmware 2.76 and IC-7100

« on: 2014-02-03, 19:03:12 »

The new FW 2.77 solves my Problems.

Manny thanks for the good support.

73
Oliver

3

General discussion forum / Re: Firmware 2.76 and IC-7100

« on: 2014-02-03, 11:13:28 »

Yes, it is the same.

4

General discussion forum / Re: Firmware 2.76 and IC-7100

« on: 2014-02-02, 22:22:36 »

Now i have update my TS-480 equipment (with WIFI) to 2.76.
It works fine too.

73
Oliver

5

General discussion forum / Re: Firmware 2.76 and IC-7100

« on: 2014-02-02, 21:45:59 »

I use the WiFi with my IC-7100.
I donīt know if the controller restarts or lost WiFi connection.

My TS-2000 with Lan connection works fine with Firmware 2.76.

73
Oliver

6

General discussion forum / Firmware 2.76 and IC-7100

« on: 2014-02-02, 19:17:28 »

Hallo,

I upgrade my IC-7100 control Unit (with W-LAN modul ) to Firmware 2.76.
After ca 5-10 minutes the Controller restarts, then it works for ca 5 minutes and restart again..... and so on.

After downgreat to 2.75 the unit works fine.

73
Oliver

7

General discussion / Re: Windows 8.1 x64 problems !

« on: 2013-10-27, 13:53:40 »

Has anyone tested version 1.6.10 with Windows 8.1

8

General discussion / Re: Windows 8.1 x64 problems !

« on: 2013-10-21, 09:43:36 »

Hallo,

on a system I get to sample only up to the selection of the network card.
When I click OK, nothing happens.


73..
Ole

9

General discussion / Windows 8.1 x64 problems !

« on: 2013-10-20, 13:21:42 »

Problems with version 1.68 and 1.69 with Windows 8.1?

I use Windows 8.1 64-bit and have on multiple systems problems.
Can not start... No Com ports..etc.

The 1.67 version works  fine.

best regards
Ole

10

General discussion forum / Kenwood TS-2000 Twin

« on: 2012-11-19, 10:49:49 »

Hello Ham friends,

someone has tested the Kenwood TS-2000 via RS232 port or the panel-port with a second TS-2000 to operate like Yaesu Twin?

Thanks
Ole
DH8AAA

11

General discussion forum / Re: IC-R2500 switch on and off

« on: 2012-01-30, 09:10:48 »

Many thanks to the development team and especially to Mike for the solution of my problem with the Icom IC-R2500 (on / off).

With the firmware 2.52, the problem seems solved.

A very good and fast support.

Best regards

Oliver
(DH8AAA)

12

General discussion forum / Re: RC 2000 - 0,1KHz step

« on: 2012-01-04, 19:41:25 »

Hallo,

you can press the Main Dail on RC-2000 and swtich from Multi (1KHz) to Tun (0,1KHz).

73
Oliver

13

General discussion forum / IC-R2500 switch on and off

« on: 2012-01-01, 15:49:00 »

Hello and a happy new year

I have a problem with my IC-R2500 firmware 2.20. and two MK2 FW.2.50.

The system works fine but....
After a few minutes turn off remote operation of R2500. The control unit also turns off but the RTP / UDP and audio status and
UDP cmd status remain connected. After a few minutes the R2500 and the control unit switches back on. This process is repeated again and again.
If I use program mode 9 (IC-E2820), I have other problems but not the on and off.

What can I do.

best regards
Oliver
DH8AAA