Messages

1

Configuration, RRC 1258 / Re: RRC and the Icom 9100

« on: 2012-04-05, 00:10:24 »

"If you connect the PC with a serial connector to Control-RRC com2 you have to set com2 to "Logically in parallell with com0"


We had it set to Icom CIV. Setting it to Logically in parallell with com0 now works.
Thanks!

2

Configuration, RRC 1258 / RRC and the Icom 9100

« on: 2012-04-01, 21:34:03 »

Jan,
Trying to get the RRC to work with the Icom 9100 using a pair of RRC1258 mkii and the Icom RS-BA1 remote control software.

The Radio RRC connects to the Control RRC but the RS-BA1 software does not find the radio.

I have the Icom software and the radio set to match the RRC at 9600 bps com 1 N81 . Icom software and radio use 7C as the CI-V address.  There is also an address setting for the CI-V RS-BA1 in the BA1 setup. It is currently set to E0.

I have attached my two RRC  unit configuration files. Could you have a look to be sure I have them configure properly?

Is there an easy way to tell if the control unit is talking to com 1 ( and the icom software or the connection utility) on the laptop at the remote end?  There are so many places that I might have missed something its hard to divide and conquer.

Thanks for your help!

3

Configuration, RRC 1258 / Re: Error 31 while upgrading

« on: 2012-01-26, 21:24:40 »

JMP-1 and JMP-2 needed to be removed. Its working now. Thanks!

4

Configuration, RRC 1258 / Re: Error 31 while upgrading

« on: 2012-01-26, 17:31:14 »

Yes ,"Use USB Com Port as COM0" is = No (on the radio settings page). Here are the settings from the non functional control unit. I am able to get my other two units to work. 

5

Configuration, RRC 1258 / Re: Error 31 while upgrading

« on: 2012-01-20, 18:59:27 »

If I hold the power button on the RC-2000 down and reload the status page the radio does go from OFF to ON but the RC-2000 display does not wake up like it does with the other two control units. As long as I  hold down the power button on the RC-2000 the status page says radio on, once I let it go o the power button the radio status immediatly goes back to off.

So it looks like its trying???

6

Configuration, RRC 1258 / Re: Error 31 while upgrading

« on: 2012-01-18, 23:39:28 »

No there does not seem to be any difference in thestatus screen before and after I hit the power switch on the RC-2000

7

Configuration, RRC 1258 / Re: Error 31 while upgrading

« on: 2012-01-13, 20:38:52 »

i don't see anything else in the other part field except 0.0.0.0. I attached a few screen captures...

8

Configuration, RRC 1258 / Re: Error 31 while upgrading

« on: 2012-01-12, 18:57:43 »

But i can not connect to the Radio from the control.

I have a working pair connect to my TS-2000. If I replace the working control unit with this unit (no boot loader and FW 2.05) it will not connect. I saved the setting.bin from the working unit and downloaded to this unit, but it will not connect.
In the status screen the "other part field" shows  0.0.0.0. (correct IP is entered into the SIP contact field)  On the working unit it displays the proper IP address.

 The bootloader field on the non working unit says <= 1.7. Do I need a new bootloader and how do I get the FW version to read 2.5 in the setup application? It currently reads 2.5 on the HTML status screen but 000.020.050 for FW and 000.000.002 for hardware on the setup app.

The SN of this non working unit is 3109 The working unit is 4475

9

Configuration, RRC 1258 / Re: Error 31 while upgrading

« on: 2012-01-12, 18:06:56 »

Yes the FW upgrade via USB now works. But it still reports the FW version as 2.05 and not 2.5. Is this normal?

10

Configuration, RRC 1258 / Error 31 while upgrading

« on: 2012-01-10, 18:30:14 »

I have 3 sets of the RRC1258MkII.

The first two sets FW upgraded with no problem using USB.

The third set will not upgrade FW using USB. I get the Error 31 message.

After failing trying USB, I was able to upgrade the 3rd unit's FW using the web, I think, But usb still is dosen't work.

The revision of boot loader on the failed unit says N/A and FW is now version is 000.000.002.050 unlike the other two sets that report firmware is 2.50. and boot loader is 1.9. HW is ver 6 on all sets.  Have not tried to config this unit for radios yet, but the other two are working well.

How do I fix the missing bootloader and FW revision number?