Author Topic: Switching between PC-Client and TS-480 Control Head?  (Read 10987 times)

NZ5E

  • Jr. Member
  • **
  • Posts: 42
    • View Profile
I currently have the 2-box Remoterig system connected in Mode 5 to a Kenwood TS-480.  If I add the PC-Client hardware/software, can I leave the Remoterig Radio Unit in Mode 5 and operate with the TS-480 Remote Head at my home and the PC-Client on my laptop from other locations without reconfiguring everything?

I realize that I can download the PC-Client software from the website.  What are my options for purchasing the hardware?

dj0qn

  • Hero Member
  • *****
  • Posts: 2223
    • View Profile
    • DJ0QN / K7DX
    • Email
Re: Switching between PC-Client and TS-480 Control Head?
« Reply #1 on: 2010-11-25, 14:40:06 »
Just make sure that you leave your head turned off when you leave
and the RRC setting "auto connect" to "no", and you will be fine.

73,
Mitch DJ0QN / K7DX

ZL4PLM

  • Newbie
  • *
  • Posts: 12
    • View Profile
Re: Switching between PC-Client and TS-480 Control Head?
« Reply #2 on: 2010-11-30, 11:21:58 »
Mitch

what would be the setup on the RRC for this

I have the same setup Id like to try

dj0qn

  • Hero Member
  • *****
  • Posts: 2223
    • View Profile
    • DJ0QN / K7DX
    • Email
Re: Switching between PC-Client and TS-480 Control Head?
« Reply #3 on: 2010-11-30, 11:43:46 »
Just go into the box (control side) and go to "Radio Settings". Then
make sure that "Auto connect" is set to no.

That's all there is to it, except making sure that your remote head is off.

I have played around and been able to get control using the PC Client,
even when the head was connected, but I would not recommend this.

73,
Mitch DJ0QN / K7DX

ON4AOI

  • Sr. Member
  • ****
  • Posts: 295
    • View Profile
    • Email
Re: Switching between PC-Client and TS-480 Control Head?
« Reply #4 on: 2010-11-30, 13:35:46 »
I have played around and been able to get control using the PC Client,
even when the head was connected, but I would not recommend this.

Not sure if this can be problem Mitch, if you use the original kenwood soft it works also perfect
maybe you can have some timing problems if you use a different network provider (GSM + internet)

Guy ON4AOI

dj0qn

  • Hero Member
  • *****
  • Posts: 2223
    • View Profile
    • DJ0QN / K7DX
    • Email
Re: Switching between PC-Client and TS-480 Control Head?
« Reply #5 on: 2010-11-30, 13:40:06 »
Hi Guy,

I am not sure what you mean, the question was only the best
way to switch between the remote head and PC Client. There
is no other software involved, and the network is not an issue.

73,
Mitch DJ0QN / K7DX

ON4AOI

  • Sr. Member
  • ****
  • Posts: 295
    • View Profile
    • Email
Re: Switching between PC-Client and TS-480 Control Head?
« Reply #6 on: 2010-11-30, 14:54:07 »
Hi Mitch,
was just given comments about using both at the same time, I dont have problems
when I do it

Guy ON4AOI

dj0qn

  • Hero Member
  • *****
  • Posts: 2223
    • View Profile
    • DJ0QN / K7DX
    • Email
Re: Switching between PC-Client and TS-480 Control Head?
« Reply #7 on: 2010-11-30, 14:57:56 »
Hi Guy,

Yes, I have also managed to have both working at the same time, but
that is not the way it is supposed to work. I assume that this "feature"
may be fixed in a future firmware release or of the PC Client.

Better to do it right! ;-)

73,
Mitch DJ0QN / K7DX