Author Topic: Webswitch will not recognize its USERID and password  (Read 8956 times)

wb7ely

  • Jr. Member
  • **
  • Posts: 54
    • View Profile
    • WB7ELY
    • Email
I cannot seem to access/change my webswitch 1216H settings. The help page states that the "webswitch uses its generated password and userid" on the dns setup page. I have entered the userid and password using the show password button and it is not recognized/rejected. (see the the attached screen shot)
please help-mitch are you still out there?
de dave
WB7ELY
//Dave WB7ELY

wb7ely

  • Jr. Member
  • **
  • Posts: 54
    • View Profile
    • WB7ELY
    • Email
Re: Webswitch will not recognize its USERID and password
« Reply #1 on: 2021-04-10, 01:30:24 »
Hey Wb7ELY- I understand that you CAN ACCESS the webswitch's webpage via the microbit dns but you cannot change any parameters? And this is due to the userid and password are not recognized? that's crazy hopefully someone can help you out, otherwise, check other webswitch options and call it bricked through no fault of your own..
//Dave WB7ELY

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3041
    • View Profile
    • sm2oan
    • Email
Re: Webswitch will not recognize its USERID and password
« Reply #2 on: 2021-04-10, 08:48:14 »
if you connect USB and start Microbit setup manager, there is a "set default"option under the advanced tab which resets the password.

Always use your own passwword, if you leave it without and it's reachable over ethernet, robots will set password to it again

73 de mike

sm0fzh

  • Newbie
  • *
  • Posts: 5
    • View Profile
    • Email
Re: Webswitch will not recognize its USERID and password
« Reply #3 on: 2022-06-22, 17:58:41 »
Hallo
My old Webswich 1216H sw 4.27 Dec 22 2016 Sn 1768 is totaly locked by some unknown password.
I can not come into the settings. All is blocked.

On an other of my Webswitches 1216H I can go via IP-settings and set the password.

What can I do.
SM0FZH

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3041
    • View Profile
    • sm2oan
    • Email
Re: Webswitch will not recognize its USERID and password
« Reply #4 on: 2022-06-22, 20:03:50 »
Hej

det är samma svar som ovan. Anslut USB och kör setup manager, under advanced finns ett val set defaults

/micke

sm0fzh

  • Newbie
  • *
  • Posts: 5
    • View Profile
    • Email
Re: Webswitch will not recognize its USERID and password
« Reply #5 on: 2022-06-23, 11:47:25 »
Problem med Webbswitch 1216  "allt" är låst av okänt lösenord.
Jag försökte:
Anslut via USB och Setup Manager senaste version.
Utan samtidig Ethernet ingen Websida
Find device
Websida som bara systeminfo kan öppnas allt annat år blockerat.
"Advanced settings" kräver lösenord och är blockerat.
Finns det någon lösning åt detta problem. Dina råd fungerar inte då allt är låst.
Eberhard

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3041
    • View Profile
    • sm2oan
    • Email
Re: Webswitch will not recognize its USERID and password
« Reply #6 on: 2022-06-23, 11:52:27 »
Hej

du skall göra "set default" från advanced menyn i setup managern, då du har ansluten USB, Inte göra nått i webinterfacet

då tas lösenordet bort och den får default ip-adress, du kan sen surfa till den på vanligt sätt och hitta den under find devices

/micke


sm0fzh

  • Newbie
  • *
  • Posts: 5
    • View Profile
    • Email
Re: Webswitch will not recognize its USERID and password
« Reply #7 on: 2022-06-23, 13:31:59 »
tack, nu fungerar det.  Ska skriva upp allt för nästa gången.
Eberhard