Remote Rig

RRC 1258 Support in English => Configuration, RRC 1258 => Topic started by: VK3OE on 2013-07-10, 09:32:42

Title: Icom 7100 CIV control
Post by: VK3OE on 2013-07-10, 09:32:42

Hello,

I have acquired an IC-7100 and wish to use the control head ( which is on COM 0 ) and the CIV from the remote unit at the same time so that I can use HRD or any similar logging program to get the frequencies and modes of the remote unit into the computer. I have tried to configure this arrangement but the CIV backhaul that I use with the IC-7000 is precluded as it requires to place COM2 logically in parrell with COM0 at the control which is in conflict with the IC 7100 configuration.

Ideas please??

Andrew
VK3OE/VK3OER

Title: Re: Icom 7100 CIV control
Post by: sm2o on 2013-07-10, 13:29:05

Hi

Set com2 to mode 2 in both RRC:s.

73 de mike

Title: Re: Icom 7100 CIV control
Post by: EA1AF on 2013-08-20, 01:41:35

Hello,

I have a problem also with the CI-V and IC-7100.

I have selected Mode 2 in both RRC´s in COM2.
I use a straight RS232 cable from Control to RRC and a TTL converter from the rear part or the radio (remote) to RRC.

The cable is working OK, tested without the remote system.

I tried all the baudrate speeds and configurations in the mode 2 of COM2.

I don´t know where is the problem. ¿ Any ideas to test?

Thanks in advance.

EA1AF - David

Title: Re: Icom 7100 CIV control
Post by: sm2o on 2013-08-20, 11:11:06

What control software do you use ?

/mike

Title: Re: Icom 7100 CIV control
Post by: EA1AF on 2013-08-20, 12:05:39

Logger32 here.

EA1AF - David

Title: Re: Icom 7100 CIV control
Post by: ON4AOI on 2013-08-20, 15:33:44

Hola David,

"I tried all the baudrate speeds and configurations in the mode 2 of COM2"
How is the baudrate set in the IC-7100 ? if auto change to 9600 or 19k2

Guy ON4AOI

 

Title: Re: Icom 7100 CIV control
Post by: EA1AF on 2013-08-20, 16:22:52

Hello Guy, the IC-7100 has in the CI-V options:

CI-V transceive: ON
CI-V Address: 88h
CI-V Baud Rate: I tested all the options from 300 to 19200 and AUTO

EA1AF - David

Title: Re: Icom 7100 CIV control
Post by: ON4AOI on 2013-08-20, 18:22:20

David,
this wan't  probably change anything
but put CI-V tranceive to OFF

Guy  ON4AOI

Title: Re: Icom 7100 CIV control
Post by: EA1AF on 2013-08-20, 19:40:22

Hello again,

Is not a problem of the IC-7100, the CI-V is working well with the direct connection to PC, out of the remote instalation.

The TTL converter is from Icom, is not a cheaper one.

I find that is a problem when I connect the RRC´s and the data throught the COM2.

EA1AF - David

Title: Re: Icom 7100 CIV control
Post by: ON4AOI on 2013-08-20, 20:28:31

David,
some programs don't like CI-V tranceive = ON