Messages

1

General discussion forum / Re: Stange LAN behavior

« on: 2022-10-10, 06:00:01 »

Graham-san;

After countless challenges and tries, I have finally found the cause of the LAN Problem.
The unstable behavior of connection was caused by the LAN cable which looked just
fine from outside. My goodness!

73
Akira
JI1HNC

2

General discussion forum / Re: Stange LAN behavior

« on: 2021-11-23, 02:32:01 »

Graham-san;

Thank you for your advice.
I went to the remote shack and updated to 4.27 over weekend.

It seems somehow improved but not drastically.
Also, I noticed that RC1216H was just like "breathing" about
every 10 seconds to send 1K-FA's control view.

I will let you know when I find out the cause.

73
Akira
JI1HNC

3

General discussion forum / Re: Stange LAN behavior

« on: 2021-11-20, 03:00:27 »

Graham-san;

I have the same problem on RC1216H and SPE 1K-FA pair recently.
Which version of firmware do you use?
I am still using v.4.26.

Regards,

Akira
JI1HNC

4

Configuration, Webswitch 1216H / RC1216H and Expert 1K-FA

« on: 2016-01-11, 09:34:59 »

Mike-san;

I set up RC1216H and Expert 1K-FA a couple of days ago and
they worked fine via internet until this morning.
This evening, however, they does not work.
I turned on MAIN PWR-OK(turned red),ON OFF-OK(turned red),
the green status on the top right corner stopped blinking and said
starting..., OUTPUT POWER and Temp showed this morning's
status (half and 10c). But the window turned Off/Unknown in about
7 seconds.
I tried several times but resulted same. Serial connection has not
established yet.

Do you have any idea to fix them?

Regards,

Akira
 

5

Configuration, Webswitch 1216H / Re: Rotator control 1216L A/D error

« on: 2015-06-15, 08:46:04 »

Mike-san;

I re-installed 1216-L which you sent me and it works just fine!
I still have no ideas about what went wrong with my original
1216-L board.

Any way, Thank you very much for your kind support.

Regard,

Akira
JI1HNC

6

Configuration, Webswitch 1216H / Re: Rotator control 1216L A/D error

« on: 2015-06-02, 01:41:39 »

Mike-san;

Have you found any malfunction in my 1216L ?
Further advice would be appreciated.

Regards,

Akira
JI1HNC

7

Configuration, Webswitch 1216H / Re: Rotator control 1216L A/D error

« on: 2015-05-03, 14:06:24 »

Mike-san,

Thank you for your reply, spending weekend spare time.
No lightning atack has been recognized, but I will send it to Microbit
for investigation.

Regards,

Akira

8

Configuration, Webswitch 1216H / Re: Rotator control 1216L A/D error

« on: 2015-05-03, 01:46:40 »

Mike-san,

Thank you very much for your advice. I released all wires to 1216L and re-connected them
but the situation remains unchanged.
Worse, A/D value does not change while pot voltage is moving.
When I restart webswich1216H, A/D value changes. (randomely but not always)

firmware version: HAM4.17
pot voltage is measured on the printed circuit of 1216L

Further advice will be very much appreciated.

Akira

9

Configuration, Webswitch 1216H / Re: Rotator control 1216L A/D error

« on: 2015-04-29, 03:22:23 »

Hi

My 1216L-5 has been working fine for 8 months, however, A/D values
jumped randomely form time to time recently.

System info shows "HW >= 5, FW 5" and the LED blinks once a second
properly. G-1000 pot voltage is mooving smoothly from 0V to 4.6V.

Your assistance would be very welcome.

Regards,

AKira

10

General discussion forum / Re: Multiple 1216L Rotator control Units on a single Webswitch?

« on: 2014-02-06, 14:28:05 »

Thank you, I understand.

Akira

11

General discussion forum / Re: Multiple 1216L Rotator control Units on a single Webswitch?

« on: 2014-02-06, 05:53:51 »

Hello;

I have a similar question.
Can I use 1216L and 1216S for rotator contorol simultaneously on
a single 1216H?

Akira Yamamoto
JI1HNC

12

General discussion forum / Re: RRCMicro Client password problem

« on: 2013-06-15, 06:33:49 »

Hi Mike;

Recently I bought a RRCmicro client and have the same trouble regarding
password issue; "passwoed not accepted".

I do not use any SIP password, and my RRC1258mk2 pair has been working very fine
for 2yeas.

Thanks, in advance, for your help.

Akira
JI1HNC