1
General discussion / Re: Connected to sip - but Connection status Faulty ?
« on: 2015-03-16, 19:15:12 »
do sp2xdw@wp.pl and sp2xdw@icloud.com pse
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
General discussion / Re: Connected to sip - but Connection status Faulty ?
« on: 2015-03-16, 18:51:38 »
Name Value
Control panel ON
Radio ON
Connection status Faulty(See below)
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status Error(0)
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
I changed to 6060 but still UDP error --- sp2xdw@icloud.com
Dual Rx 0
Current audio packet size 20
Current audio quality 1 - Linear 12 bits 8 kHz
External IP dwydra.dyndns.org
SIP Out port 6060
SIP In port 6060
Audio Out port 16492
Audio In port 11000
Command Out port 12000
Command In port 12000
External SIP In port 6060
External Audio In port 11000
External Cmd In port 12000
Control panel ON
Radio ON
Connection status Faulty(See below)
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status Error(0)
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
I changed to 6060 but still UDP error --- sp2xdw@icloud.com
Dual Rx 0
Current audio packet size 20
Current audio quality 1 - Linear 12 bits 8 kHz
External IP dwydra.dyndns.org
SIP Out port 6060
SIP In port 6060
Audio Out port 16492
Audio In port 11000
Command Out port 12000
Command In port 12000
External SIP In port 6060
External Audio In port 11000
External Cmd In port 12000
3
General discussion / Re: Connected to sip - but Connection status Faulty ?
« on: 2015-03-08, 13:10:17 »
Dear,
Mitch DJ0QN / K7DX
I have the same problem. For some time, only occasionally reaches connectivity . Most of the time a message is displayed below: UDP cmd status Error(0)
Name Value
Control panel ON
Radio ON
Connection status Faulty(See below)
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status Error(0)
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
Current audio packet size 20
Current audio quality 1 - Linear 12 bits 8 kHz
External IP dwydra.dyndns.org
SIP Out port 5060
SIP In port 5060
Audio Out port 20004
Audio In port 11000
Command Out port 12000
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 83.8.145.90
Input 0 High
Input 1 High
Input 2 High
Output 0 High
Output 1 Low
Output 2 Low
DNS status OK, dwydra.dyndns.org = 83.8.145.90
Active profile: Profile 1
PTT status: OFF
Mitch DJ0QN / K7DX
I have the same problem. For some time, only occasionally reaches connectivity . Most of the time a message is displayed below: UDP cmd status Error(0)
Name Value
Control panel ON
Radio ON
Connection status Faulty(See below)
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status Error(0)
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
Current audio packet size 20
Current audio quality 1 - Linear 12 bits 8 kHz
External IP dwydra.dyndns.org
SIP Out port 5060
SIP In port 5060
Audio Out port 20004
Audio In port 11000
Command Out port 12000
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 83.8.145.90
Input 0 High
Input 1 High
Input 2 High
Output 0 High
Output 1 Low
Output 2 Low
DNS status OK, dwydra.dyndns.org = 83.8.145.90
Active profile: Profile 1
PTT status: OFF
4
General discussion forum / Re: Help configuring Serial Port
« on: 2014-05-11, 01:20:32 »
Ero http://qrz.com/db/IK1DYS. Purtroppo, questo sistema non mi piace. Alla ricerca di "Y" Cavo per Ultrabeam come antenna SteppIR collegamento SteppIR-TS-480-PC. Il mio attuale sistema di controllo remoto "Remoterig" consente di chiamare: 1 rotore 2 TS-480 port "CAT" Kenwood steer Ultrabeam.
Sto cercando una soluzione del genere che solo "Remoterig" controllare il rotore 1, 2 e 3 UltraBeam TS-480 da HDRLog. Sto contando sul vostro aiuto.
I am looking for equivalent Y-cable (this is for SteppIR) through which I can control remotely via a program HDRLog Kenwood TS-480 and at the same time the CAT port control antenna Ultrabeam. Unfortynatelly Remoterig has only 2 serial ports. One of them allows me to control the rotor. Second I can use to control radio or Ultrabeam.
Sto cercando una soluzione del genere che solo "Remoterig" controllare il rotore 1, 2 e 3 UltraBeam TS-480 da HDRLog. Sto contando sul vostro aiuto.
I am looking for equivalent Y-cable (this is for SteppIR) through which I can control remotely via a program HDRLog Kenwood TS-480 and at the same time the CAT port control antenna Ultrabeam. Unfortynatelly Remoterig has only 2 serial ports. One of them allows me to control the rotor. Second I can use to control radio or Ultrabeam.
5
General discussion forum / Re: Ultrabeam remote control
« on: 2014-04-09, 00:24:14 »
I use CAT to control the Ultrabeam @ RRC-1258MkIIs to control the Kenwood TS-480.
Pages: [1]