Messages

1

General discussion forum / Re: Serial connection hangs after 10 seconds (TS-570)

« on: 2016-02-24, 20:30:42 »

It was worth trying it but com2 via USB did not solve this issue.
Thanks for your help anyway.

2

General discussion forum / Re: Serial connection hangs after 10 seconds (TS-570)

« on: 2016-02-24, 10:19:43 »

Ok got it know.
Will try to control the TS-570 via USB on control-rrc.

3

General discussion forum / Re: Serial connection hangs after 10 seconds (TS-570)

« on: 2016-02-23, 21:31:03 »

Hi Dennis,
Iam not sure if I do understand your question completely but I tried the onboard comport (com1) on my laptop and 2 different USB to RS-232 converters (com9 and com10) and another laptop. The serial connection is needed to control the transceiver because the TS-570 does not have a separate front panel.

4

General discussion forum / Re: Serial connection hangs after 10 seconds (TS-570)

« on: 2016-02-22, 10:23:18 »

Ok. I tried another PC (win8)  with a Startech USB to RS232 converter. But still the same problem. My conslusion, the TS-570 is not suitable to work with remoterig unfortunately . 

5

General discussion forum / Re: Serial connection hangs after 10 seconds (TS-570)

« on: 2016-02-21, 15:44:40 »

Hi Mike,

I tried mode 1 and 3. Mode 3 is a bit better and mode 1 is very slow and puts the TS-570 to wrong frequencies. 
I also installed a USB to RS-232 converter. It works better/longer now but after 5 minutes or so the connection goes down again. Will try another PC later.

If I switch over the cable to my TS-480 it all works fine with this setup and settings. So I agree with you the problem could be in the TS-570 firmware. Probably Iam the first person who is using a TS-570 with remoterig.

Mark.

6

General discussion forum / Re: Serial connection hangs after 10 seconds (TS-570)

« on: 2016-02-21, 08:10:45 »

Thanks for your help Mitch, it is much appreciated.

I changed com0 to 9600. Iam using the latest firmware.


Info

Name   Value
Company   Microbit
Product   1258
PID   4
Version   7
HW   8
Software   2.90
Bootloader   1.10
Compiler   4.6.2
Build   Feb 17 2016 10:16:14
ROM/RAM   481192/44080
ETH-RAM   2944 (max 3kB)
USB-RAM   15352 (max 16kB)
Battery-RAM   4
ResetSrc   0 [3]
Last WD Reset   9
Uptime   0 Days, 0 Hours, 0 Mins, 8 Secs
    
Serial number   7331
MAC address   00:1e:fd:01:93:43
IP address   192.168.178.3
Netmask   255.255.255.0
Gateway   192.168.178.1
DNS   212.54.44.54
Wi-Fi network   module not present

7

General discussion forum / Re: Serial connection hangs after 10 seconds (TS-570)

« on: 2016-02-20, 21:56:22 »

Settings

Unit ID (Banner)   Control RRC in shack
DHCP   0
IP   192.168.178.3
Netmask   255.255.255.0
Gateway   192.168.178.1
Dns server   212.54.44.54
Eth-type   5
IP-interface   0
Web page user   
Web page pwd   
Web page user(saving)   
Web page pwd(saving)   
Program mode   4
Control panel   1
Sip password   
Sip contact(Radio RRC IP/hostname)   192.168.178.2
Auto connect   0
Audio quality   5
Audio dual-rx   0
Audio left/right ch swap   0
Codec out gain   255
Codec inp gain   18
Codec inp HPF Hz   3
Codec inp preamp   1
Codec inp attenuation   0
COM0 baudrate   57600
COM0 data bits   8
COM0 stop bits   1
COM0 parity   0
COM0 Program mode 3 char timeout   2
Use USB Com Port as COM0   0
COM1 mode   0
COM1 baudrate   9600
COM1 data bits   8
COM1 stop bits   1
COM1 parity   0
COM1 rts/cts   0
COM1 terminator (hex)   00
Use USB Com Port as COM1   0
COM2 mode   4
COM2 baudrate   9600
COM2 data bits   8
COM2 stop bits   1
COM2 parity   0
COM2 terminator (hex)   00
Use USB Com Port as COM2   0
COM3(Extra) mode (USB-COMFSK)   0
UDP cmd port   13002
UDP audio port   13001
SIP port   13000
Web server port   80
Telnet server port   23
Rx jitter buffer size   4
Rx jitter delay   3
Audio packet size (ms)   20
RTP tx mode   0
Disable audio tones   0
Audio tones -db [70-0]   30
IP identification (morse)   0
Full duplex   0
PTT-off mute delay   0
IP Type-of-Service (dec)   0
Yaesu power-on/off   0
UDP antenna-switch port   13010
UDP cmd min-data-size   0
Use common network settings   0
Check interval   0
DDNS Host name   0
Own host name   

8

General discussion forum / Re: Serial connection hangs after 10 seconds (TS-570)

« on: 2016-02-20, 21:30:00 »

Just checked.

Both RRC's: Radio settings> program mode> 4 - Yaesu, Kenwood, Elecraft.

9

General discussion forum / Serial connection hangs after 10 seconds (TS-570)

« on: 2016-02-20, 21:00:05 »

Hi,

I have been using remoterig successfull with a TS-480. But now I want to get my TS-570 working with remoterig. I made all the cables and did the configurations. Everyting is working except the CAT control via remoterig.

When I connect the TS-570 directly to my computer cat control does work fine (9600, 8, 1, N). But with remoterig in between HRD gives a disconnect message after +/- 10 seconds. I am using COM2 on remoterig.

When the disconnect message appears in HRD there are 2 ways to get the connection run again:
1. switch off and on the TS-570, the connection is working again for +/- 10 seconds
2. Remove both serial cables from radio RRC  and control RRC and put them together (remoterig is bypassed).

When the connection drops out  "CTRL" is not longer displayed in the TS-570 display, but after switching off and on the TS-570 CTRL is displayed again. (CTRL indicates the radio is controled via serial).

It looks like the TS-570 does not like the delay? Both remoterig boxes are on my desk connected to a switch.

Iam using COM mode 4, 9600  baud, 8, 1 , 0 ,00

I also tried COM1 but it did not help.

2 standard RS-232 cables are used (male-female), 1 with a gender changer (between radio-rrc and radio).