1
Configuration, RRC 1258 / Re: TS710G
« on: 2014-11-23, 21:28:31 »
Attempt to attached the HTML file
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Configuration, RRC 1258 / Re: TS710G
« on: 2014-11-23, 21:23:42 »
Thanks Mike,
I guess I timed out and didn't realize it...
Attached are the HTML files,
I have (1) TS480 which power up just fine but we have not tested anything else...
I have (2) TS710 which will not communicate or something to each other, will not power up.. I have compared the setup to the
480 but nothing jumps off the page. Both units work fine when direct connected to each other.
I have made the cables twice unless I'm missing something in the config instructions just downloaded from your site.
These are all new units, just arrived within the last week
All (3) units are on the same network, closed, not going to the outside world.
This is a public safety 911 center in their RACES room.
Thanks for any support on this and any other suggestions for a successful installation.
I guess I timed out and didn't realize it...
Attached are the HTML files,
I have (1) TS480 which power up just fine but we have not tested anything else...
I have (2) TS710 which will not communicate or something to each other, will not power up.. I have compared the setup to the
480 but nothing jumps off the page. Both units work fine when direct connected to each other.
I have made the cables twice unless I'm missing something in the config instructions just downloaded from your site.
These are all new units, just arrived within the last week
All (3) units are on the same network, closed, not going to the outside world.
This is a public safety 911 center in their RACES room.
Thanks for any support on this and any other suggestions for a successful installation.
3
Configuration, RRC 1258 / TS710G
« on: 2014-11-19, 15:24:00 »
I have purchased (3) 1258MKiiS kits, will be using them on the Kenwood 480SAT and 710G.
The 480 interface went good, all seems to working however I have not been able to get
the 710G to power up.
I have double checked and even made more interface cable for both ends,
I have even tried the second set of 1258s but I still cannot get the
710 to power up remotely. I have used the factory cable to and connected the
control back to the radio all works fine... just no remote control.
triple checked the config of both sets of 1258 with no avail..
any thoughts where to go next?
My phone is 606-878-8012, Kentucky, thanks
The 480 interface went good, all seems to working however I have not been able to get
the 710G to power up.
I have double checked and even made more interface cable for both ends,
I have even tried the second set of 1258s but I still cannot get the
710 to power up remotely. I have used the factory cable to and connected the
control back to the radio all works fine... just no remote control.
triple checked the config of both sets of 1258 with no avail..
any thoughts where to go next?
My phone is 606-878-8012, Kentucky, thanks
4
General discussion forum / Remote Rig Purchase
« on: 2014-10-23, 00:15:56 »
I'm a communications shop in Kentucky, I have limited experience with amateur radio equipment.
I'm providing a upgrade to the local RACES equipment at a local 911 Communication Center.
They have folks certified to use the equipment but they are not technical so.....
I specs tell me I MUST remote control (2) Kenwood TS480SAT and (1) Kenwood TM-D710GS
radios over an IP connection. I have called a couple amateur radio locations but neither can tell
me what parts I need to accomplish this task or even tell me if it can be done.
I would greatly appreciate any information and support this group can provide,
location to purchase, ease of installation, concerns, material and parts required (other than the radios themselves),
dos and don'ts.
Thanks in advanced.
I'm providing a upgrade to the local RACES equipment at a local 911 Communication Center.
They have folks certified to use the equipment but they are not technical so.....
I specs tell me I MUST remote control (2) Kenwood TS480SAT and (1) Kenwood TM-D710GS
radios over an IP connection. I have called a couple amateur radio locations but neither can tell
me what parts I need to accomplish this task or even tell me if it can be done.
I would greatly appreciate any information and support this group can provide,
location to purchase, ease of installation, concerns, material and parts required (other than the radios themselves),
dos and don'ts.
Thanks in advanced.
Pages: [1]