Messages

1

General discussion forum / Re: TS-480 Serial port settings

« on: 2016-01-07, 17:15:22 »

Has anyone tried this?

2

General discussion forum / TS-480 Serial port settings

« on: 2016-01-06, 15:27:23 »

   I have the remote rig setup and It is simply amazing I bought a second unit for another remote location. The question I have is I am trying to program the radio with KRS-480 from the control side I have read other threads about problems with HRD and the Kenwood software  but this is just programing the radio can this be done with the serial ports settings port 1 on the radio side is hooked up to the radio DB-9 ? Thanks again

3

General discussion forum / Re: Still having trouble Kenwood TS-480

« on: 2015-12-21, 05:14:44 »

Thanks Mike the problem has been fixed next time I am at the remote side i will check the power supply it is a new 20 amp.

4

General discussion forum / Re: Still having trouble Kenwood TS-480

« on: 2015-12-17, 05:41:43 »

Email sent thank you

5

General discussion forum / Re: Still having trouble Kenwood TS-480

« on: 2015-12-17, 00:39:10 »

 Is anyone willing to try to connect to my 480 and see if you have the same problem getting the initial connection please email me I will send you the info thanks.

6

General discussion forum / Re: TS-480 Control head

« on: 2015-12-14, 16:37:08 »

Yes its up to date. Still having problems getting it to turn on once its on it works great!

7

General discussion forum / Still having trouble Kenwood TS-480

« on: 2015-12-11, 06:19:07 »

    So I have tested this on 2 separate local LAN's and remote I have the same problem every time i use the remote rigs.  Most all of the time the panel just gets stuck in the hello mode with no audio. If I unplug the Rj-11 and plug it back in the display and audio comes to life. I have bypassed the router and went to the cable modem no change. I also notice sometimes when I use the remote rig the decimal points are missing on the display. RR is set to mode 5. I can ping the far end with no loss both sides are on cable modems. The remote side has a straight cable RJ-11 to RJ-11 if I bypass the RR and use that cable the 480 display works just fine.  One think I notice is when I turn it on the AUX mic will come on steady red on the left and yellow on the right. after a reset the red goes out any ideas?



Company   Microbit
Product   1258
PID   4
Version   7
HW   8
Software   2.87
Bootloader   1.10
Compiler   4.6.2
Build   Aug 26 2015 11:23:58
ROM/RAM   477740/44064
ETH-RAM   2944 (max 3kB)
USB-RAM   15348 (max 16kB)
Battery-RAM   4
ResetSrc   0 [3]
Last WD Reset   9
Uptime   0 Days, 0 Hours, 6 Mins, 4 Secs
    
Serial number   9980

8

General discussion forum / Re: TS-480 Control head

« on: 2015-12-11, 00:27:18 »

Do you have any idea why? I have tried everything and bypassed the router still no change i need to remove rJ-11 and plug it in to make the 480 head come alive.

9

General discussion forum / Re: TS-480 Control head

« on: 2015-12-09, 02:41:22 »

But if I cycle power it then works? do we have any other ideas ? settings ? It does the same thing when they are hooked up to the same LAN.

10

General discussion forum / Re: TS-480 Control head

« on: 2015-12-08, 06:19:53 »

Any Ideas? anyone

11

General discussion forum / Re: TS-480 Control head

« on: 2015-12-07, 17:28:48 »

I also have them set to mode 5 and the most recent Firmware

12

General discussion forum / TS-480 Control head

« on: 2015-12-07, 16:48:14 »

   So  sometimes when i turn on the control head it just shows hello and almost gets hung up.  If i unplug the RJ-11 and plug it back it it works fine any ideas? I have no problems with audio or connecting to the remote side. Thanks