Messages

1

Configuration, RRC 1258 / data abort

« on: 2018-06-05, 23:42:28 »

hi all

since this afternoon i have this error

Data Abort at 0x00054edc, called by 0x000431f4

the status is ok, but i can't connect radio (ts480)
transferring it's ok
connection status it's ok

can anyone help me please?

nuno

2

Configuration, RRC 1258 / Re: CW problem

« on: 2017-08-08, 00:31:40 »

Hi Mitch

yes , you are right; i'm using COMEXTRA for FSK and CW.

i'm using , for test, the CW machine from logger32, and radio TX but don't transmitt CW

i've put all that you wrote, but with no results....

3

Configuration, RRC 1258 / CW problem

« on: 2017-08-07, 01:34:16 »

hi all

i've tried to put TS480 sending  CW via USB with no luck.
if i used a key connected to PAD it work's perfectly.
i've tried CW MACHINE, LOGGER32, N1MM and WINTEST and all do the same...nothing!

in FSK, USB work's fine.

control RRC
IO settings

IN0 mode   -keyer
OUT0 mode   -keyer
OUT1 mode   -I/O
OUT2 mode   -I/O
USB RTS as PTT    -Com 0
USB DTR as CW    -Com 0

radio RRC
keyer settings

PTT activated by Keyer   - yes
PTT tail delay ms [0-999]   -1



IO settings

OUT0 mode   -Keyer
OUT1 mode   -Baudot-rtty45
OUT2 mode   -I/O


any ideias?

73
nuno

4

Hardware, Cabling, Installations / Re: ts480 and digi modes

« on: 2017-06-17, 23:10:59 »

Hi Dennis
thank's for your reply

yes, i have psk sound on soundcard, i've heard it....
the TS480 doens't have DIGI mode, like ICOM have USB-D; the radio stays on USB.

i can't put psk by mike connection, when i put PTT via CAT command, the radio TX, but no audio.
when i put PTT via USB (COM) the radio doens't TX.

i think that, when i put radio TX'ing by USB command, i solve the problem

regard's
nuno

5

Hardware, Cabling, Installations / ts480 and digi modes

« on: 2017-06-17, 01:37:19 »

hi all

i´m trying to put ts480 running digi modes with remoterig , but i can't put it working.

setup is:
at panel side:  CAT on COM2,
                        usb cable
                        audio plug in between sound card output and AUX/MIC input with PIN 3 and 4 connected.

at radio side: CAT on COM2 connected to the radio
                     RJ45 cable connected between AUX/MIC and MIC in the radio.

on RRC (panel side)  i have in IO settings, USB RTS as PTT, selected to COM2 ( in my case , com13)
on RRC (radio side) i have in IO settings , OUT2 mode as PTT

if i plug the microphone, it work's; if i work FSK, it work's.

when i tried to work another digi modes doesn't works; i tried to put PTT via radio command, and the radio goes TX'ing but no audio.

if i selected PTT via COM port (auxiliary USB com port) the radio don't TX.

i've tried several program with the same result.

any ideias? what i'm doing wrong?


best 73
nuno
ct1fjo

6

Configuration, RRC 1258 / Re: ic7300

« on: 2017-03-14, 23:27:59 »

hi again

i've tried a minutes ago , with a icom706 and it work's.
the problem it's something in my 7300.
i'll go check if i can solve this.

many thank's

nuno

7

Configuration, RRC 1258 / Re: ic7300

« on: 2017-03-14, 00:56:36 »

no luck....
still not working....

i've tried as you said with USB to COM0 and TTL connection to radio.

8

Configuration, RRC 1258 / Re: ic7300

« on: 2017-03-13, 18:39:22 »

thank's

i'll go test ASAP ....

the issue about CI-V cable i didn't know....thank's.

9

Configuration, RRC 1258 / ic7300

« on: 2017-03-13, 18:11:17 »

hi all

i'm helping a friend with remoterig and i can't connect the 7300.

he bought two set's, one for ts480 and another for icom.

the 480 work's fine, but icom don't....

i've tried connect the radio by TTL and com2 , as i read in the manual; i've tried to connect com2 to com2 with no sucess; i've tried to configure with several stopbits, etc.

if i connect radio directly to PC, it's all ok.

i'm trying first to connect remoterig in my house network.
when i go to STATUS, all seems ok; transfering it's ok, and the radio it's detecet by control box.
audio it's good on the control box, but no command or TX  mode

anyone have the same problem?

bet regards
nuno