Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - VA2EBI

Pages: [1] 2
1
Configuration, RRC 1258 / Sending WAV voice messages
« on: 2024-11-20, 21:12:59 »
I regularly use N1MM Logger to send stored MC files as CW messages via F-key activation.  I have stored voice messages in my computer as WAV files.  How can I connect the computer soundcard output (via the headphone jack) to the RRC?  I assume a cable with micro-plug input and RJ-45 connector that can plug into the I/O port.  Need cable advice and I/O settings.  Anyone?

George VA2EBI

2
General discussion forum / RRC1258 firmware update
« on: 2024-07-31, 18:36:21 »
Is there any likelihood of an update to v2.95?  Would the 1258 benefit from a general "tuneup"?

George VA2EBI

3
General discussion forum / Re: I/O settings for paddle
« on: 2024-06-29, 20:45:38 »
Finally, a reply!  Thanks, Mike.  I currently have Lf delay 60 ms and Key delay 60 ms.  I don't know which of these to experiment with first.  I am fortunate to have a good internet connection with very low latency and jitter.  Is there a way to test the connection, or is experimenting with various settings the way to start?

George VA2EBI

4
General discussion forum / I/O settings for paddle
« on: 2024-06-26, 20:12:39 »
I have been using two RRC1258's and two FTDX5000's in Yaesu Twin config for five years.  I am not satisfied with the CW generated by the RRC.  What are the optimal I/O settings?  I currently have the folowing I/O settings at the Control radio:

IN0           I/O
OUT0        Keyer
OUT1        Keyer
OUT2        Keyer
USB RTS   COM1
USB DTR   COM2

At the Remote radio:

OUT0 Mode     Keyer
OUT0 on/fff     Off

OUT1 Mode     Keyer
OUT1 on/off    Off
 
OUT2 Mode     Keyer
OUT2 on/off    Off

I have a speaker in parallel with the SP output of the Control RRC.  With my FTDX5000 off, I can generate excellent CW with my Begali paddle.  When I actually key the radio, I am not totally satisfied with the quality of the CW sent over the air.  Stations copy it well enough, but it is sometimes described as "choppy" or--my term--"sloppy"  My question is:  What are the recommended settings for your RRC at the Control and Remote sites?  I use N1MM+ logger with Winkey checked, but that is not a RRC-related setting.  Just curious what settings I might want to change for improved transmitted CW.

George VA2EBI

5
Configuration, RRC 1258 / Re: WINKEY USE
« on: 2024-04-05, 00:28:42 »
Sorry, I replied to the wrong message.

Christian, like Nodir I am using the Winkey feature in the RRC1258, but I have not been satisfied with the quality of my CW.  I use a Begali Contour paddle into the PAD jack of the RRC1258, but I do not believe the quality of my transmitted CW is an issue with the paddle.  When my radio is off, I can monitor my paddle with external speakers connected to the SP jack on the Control RRC, and I am sending near-perfect code.  My remote setup is a pair of Yaesu FT5000's in Yaesu Twin configuration.  I also use N1MM Plus Logger, but I was confused by the structure of your reply to Nodir.  I would appreciate copies of your printscreens for the Control RRC I/O screen, and also your N1MM Hardware, Winkey and Mode Control screens.  I should not be sending sloppy CW.  Thank you.

George VA2EBI

6
Configuration, RRC 1258 / Re: Audio interruptions and type of service
« on: 2024-04-05, 00:26:54 »

Christian, like Nodir I am using the Winkey feature in the RRC1258, but I have not been satisfied with the quality of my CW.  I use a Begali Contour paddle into the PAD jack of the RRC1258, but I do not believe the quality of my transmitted CW is an issue with the paddle.  When my radio is off, I can monitor my paddle with external speakers connected to the SP jack on the Control RRC, and I am sending near-perfect code.  My remote setup is a pair of Yaesu FT5000's in Yaesu Twin configuration.  I also use N1MM Plus Logger, but I was confused by the structure of your reply to Nodir.  I would appreciate copies of your printscreens for the Control RRC I/O screen, and also your N1MM Hardware, Winkey and Mode Control screens.  I should not be sending sloppy CW.  Thank you.

George VA2EBI

7
Configuration, RRC 1258 / Re: Invalid settings file, wrong id tag!
« on: 2023-07-15, 21:32:53 »
Sorry, my mistake at this end.

8
Configuration, RRC 1258 / Invalid settings file, wrong id tag!
« on: 2023-07-15, 20:12:11 »
I continue to have issues connecting my control RRC1258 to the remote unit.  I have solved a problem in the past by reimporting the saved .bin file for the control unit from the most recent configuration.  I tried that again today without success.  I replaced the RRC with a backup unit, a more recent build with all the current firmware.  When I tried importing the saved .bin file, I got this error message:  "Invalid settings file, wrong id tag!"

What does that mean?  Is the .bin file not successfully imported?  How do I correct this problem?  The RRC's are not communicating.

George VA2EBI

9
Configuration, Webswitch 1216H / Most of rotator display has disappeared
« on: 2022-02-06, 05:42:48 »
I have used the Webswitch 1216-H for rotator control since last year.  A month ago, the lower 75 percent of the compass display suddenly disappeared.  The indicator and all the buttons are visible and are working properly, but I am missing most of the compass.  What would be the solution to this one?

George VA2EBI

10
General discussion forum / Re: RRC1258 with bug vs. paddle
« on: 2021-12-20, 20:16:55 »
Thanks, Mike. Follow-up question:  If I have set N1MM with RRC COMExtra to COM3 for Winkey, do I need to set COM2 Mode to Mode 8?  I tried to make that change several times, but after reset I still had COM2 Mode as “Logical parallel with COM0”.  I can’t tell if I am using the Winkey emulator or not.

George VA2EBI

11
General discussion forum / RRC1258 with bug vs. paddle
« on: 2021-12-20, 19:07:56 »
What are the settings to use a bug instead of a paddle via the RRC1258?  I could not seem to find a definitive statement in the user manual.

George VA2EBI

12
General discussion forum / Re: Keying radio with stored WAV files in SSB operation
« on: 2021-10-15, 18:54:59 »
Mike, RRC at the control side has been set for continuous RTP. 

George VA2EBI

13
General discussion forum / Keying radio with stored WAV files in SSB operation
« on: 2021-10-13, 22:45:32 »
I use N1MM Logger to send stored CW messages in contests.  For SSB contests I want to send stored WAV files.  I obviously have the WAV files in the correct directory--when I hit F4, I can hear my call in headphones connected to the headphones jack on the computer, but the audio is not getting to the mic input of the Remoterig.  The mic of my Heil headset is working fine.  I need some advice, I'm clearly doing something wrong.  Do the I/O settings have to be changed?

George VA2EBI-W1EBI

14
General discussion forum / Remoterig MkIIS Yaesu Twin
« on: 2021-09-17, 17:15:41 »
Is this a new product with amended software for Yaesu Twin operation?  I have my FTdx-5000's operating in Yaesu Twin, but still have certain radio functions that do not seem to pass via the RRC.  My remote unit is S/N 13733.  I have two control units, S/N 13802 and S/N 6954.  All are MkIIS units.  Is the Yaesu Twin version different, or is it just the internal strapping that determines the "gender" of the box?

George VA2EBI-W1EBI

15
General discussion forum / FTdx-5000 and SPE 1.3K-FA
« on: 2021-08-01, 18:39:58 »
I see a couple of posts by members using this amplifier.  I would like to connect with anyone using that amp with an FT5000.  George VA2EBI-W1EBI

Pages: [1] 2