Messages

1

General discussion forum / Kenwood TM-V7A

« on: 2020-07-11, 03:58:44 »

I have an old Kenwood TM-V7A with a separation cable with ends similar to the Icom 706.  Are there an drawings regarding using this separation cable with the TM-V7A and the RemoteRig units.
Thanks!

2

General discussion forum / IPv6 IP Address

« on: 2015-04-15, 01:05:24 »

Apparently my local comcast has changed my IP format from IPv4 to IPv6. Can oneone give me some guidance on how to correctly input my SIP CONTACT info.
Thanks in advance. Tom, W9AEB

3

General discussion forum / Re: No transmit audio on IC706MKIIG

« on: 2015-03-09, 16:26:08 »

Mike:  That was the cure --- you got it !!  THANKS for your support and time. Both are much appreciated !

Tom, W9AEB
Dave, W9DR

4

General discussion forum / Re: No transmit audio on IC706MKIIG

« on: 2015-03-09, 01:28:12 »

Mike:  Thank you very much for your suggestion and your time.  I have two of the remote rig systems of my own working perfectly and have helped others program their systems but this one has me baffled. We had the unit up and running in no time only to find that everything works perfecthly except no transmit audio. We connected to the remote from two different locations with different control heads with the same results.  We check all the red wire connections with an ohm meter and all checked out ok. If you have any other suggestions it would be appreciated! Again, thanks for your time!
Tom, W9AEB

5

General discussion forum / No transmit audio on IC706MKIIG

« on: 2015-03-08, 19:37:19 »

I have no transmit audio using my remote system ... receive audio is working fine and all other functions of the radio work when connected.  I have connected  both seperation cables with a RJ45 extender and the transmit audio works well so it seems there is something with my parameters in the RCC radio unit or possible my router settings?? I am using 1300 for sip, 1301 for audio and 1302 for cmd.
ANY HELP will be greatly appreciated --- thanks in advance...

Tom, W9AEB

6

General discussion forum / Re: Wireless broadband question

« on: 2015-03-08, 03:04:11 »

I have been using my AT&T personal hotspot on my IPhone with the control RRC unit and am operating remote moble with a 706 and no problems. You must set the DHCP on the IP Setting page to YES.

7

Configuration, RRC 1258 / UDP CMD Status Error 0

« on: 2014-06-18, 22:16:02 »

On the status page I'm getting UDP CMD =  ERROR 0.  I'm configured with an Icom 706 MKIIG.  The radio via the RRC works except I have no display.  Any ideas or suggestions would be greatly appreciated. 73, Tom, W9AEB

8

General discussion forum / Re: Display Screen on the Icom 706MKIIG

« on: 2014-06-13, 00:08:19 »

Mike thanks for your reply.  I exchanged the OPC - 581 with another I have and the issue remains. I will check the red straps when I can get to the remote site next week.  The radio is working normally except for the display. I had a QSO with a station on the last frequency the radio was tuned to before the display problem. Thanks again ..
If anyone else has any ideas it will be appreciated.

73, Tom

9

General discussion forum / Display Screen on the Icom 706MKIIG

« on: 2014-06-12, 22:34:57 »

At times when I connect to my remote the display screen on the 706 will not light but at the same time all else seems to be normal. I would appreciate any ideas. Thnks in advance!

10

General discussion forum / SteppIR power supply

« on: 2011-10-28, 00:37:50 »

Can I safely switch the 33 volt steppIR power supply with the RC 1216H?

11

General discussion forum / 706 cable problem

« on: 2011-04-26, 22:49:54 »

I have converted the Icom-cable to the 8-pol Cat-5 cable and link the two sections together with an adapter to test the wiring.   Everything seems to work fine until I attempt to transmit.  When I do engage the push to talk on the 706 mkIIg the radio shuts down [powers off] Without using the extension cable the radio operates as it should.  Any idea what the problem might be?  Thank you in advance for your help.
Tom, W9AEB