Messages

1

General discussion forum / Re: Lost connection with my Kenwood V81 V/U

« on: 2021-12-30, 16:07:28 »

Hello Mice ,

I have tried many times to restart with success both units.

This old setup that is working many years.

Which unit should I check ? Conrol unit or remote?

Which cables to check you mean?

73

2

General discussion forum / Lost connection with my Kenwood V81 V/U

« on: 2021-12-29, 09:58:52 »

Hello and Happy seasons to everybody..

Have a problem with my remote which works several years without problems.

Last days although the status is showing "connected" and no erros in status page,the display does not turn on and no sound or control of the tranceiver.

I attach a photo of webpage status of both parts and a photo of Tranceiver.

Any help would be appreciated

Dimitris SV1OZ

3

General discussion forum / Conect compatibility Kenwood TM-V71 and Kenwood TM-D700

« on: 2019-09-26, 19:33:00 »

Hello ,
I have remoterig connected and working ok with a Kenwood TM V71.

I would like to ask if I can connect with same configuration a Kenwood TM-D700 without changing cables??

73

4

General discussion forum / Re: Ethernet connection problem

« on: 2019-04-16, 15:29:09 »

I tried to change port at the router and Ethernet cable but nothing happened.

Green power led still blinking.

What do you mean cannot be repaired? From me or the company?

What is next step? Where must I send for repair??

Thank U in advance for the support

Dimitris

5

General discussion forum / Ethernet connection problem

« on: 2019-04-13, 09:21:43 »

Hello to all,

I face a strange problem with my RRC-1258 MKII interfaces..
Firstly I had the problem with my local, (shack unit).
The power green led was flashing on and off and was not connected to the internal network.
I could not see its web interface and of course it could not connect with remote interface.
I tried unplugging many times to restart the unit but only after long time off waiting  and many tries managed to be again stable green led and work flawless.
Then after some time started again the same problem and I decided to change the factory switching power supply with another I had 12.6V 1A .
Since then the local unit worked till today flawless and only 1 time made the problem .

Now have the same problem with remote interface . I checked the voltage and is 13,6 V (transceiver supply)  and making lots of restarts cannot work and remains with green power led flashing.

Is it damaged??? What can I do to recover this issue?? I am 2 weeks without remote.

Thank U in advance
Dimitris DK1OZ/SV1OZ

6

General discussion forum / Re: RRC-1258 set with Kenwood TM-V71

« on: 2019-01-28, 20:34:34 »

All ok thank you for the ideas - help

All worked perfect.

73 de Dimiris
SV1OZ

7

General discussion forum / Re: RRC-1258 set with Kenwood TM-V71

« on: 2019-01-28, 08:40:30 »

Ok thank U for the reply.
According to manual page 198 the cable connects at RRC in TTL and not AUX/MIC.
Am i missing something???
Please have in mind that all other functions work except the transmission..

Confirm please where must I look.

73

8

General discussion forum / RRC-1258 set with Kenwood TM-V71

« on: 2019-01-27, 12:39:55 »

Hello,
I have a problem with my setup.
I have connected Display and remote Rig with the RRC's and all are working perfectly. But not ...All
Only PTT is not working and can not find why???
For your info the sets are connected only in internal network without external ports etc.
When I do PTT on both Dashboards I check status and the PTT status change to ON. So i think cables and communication is all right?
I checked jumpers at remote and seem that all are according to the manual.

So why is not transmitting?
All other function work perfectly and RX works as should.
I have also attached the settings from both units if it helps...

Waiting for some help. Hope its something simple and stupid from my site hihi..


73 Dimitris

9

General discussion forum / Re: RRC-1258 works in internal network?

« on: 2017-04-17, 09:32:05 »

Thank you for the info Patrick

73 de Dimitris DK1OZ

10

General discussion forum / RRC-1258 works in internal network?

« on: 2017-04-16, 12:07:21 »

Hello,
I have a question before I buy a set for remote control.

Is this working if I use it on the same router remote and local control unit with internal IP

Thank you in advance and Happy Easter

Dimitris

11

General discussion forum / Re: New Problem Identified: Tip if RemoteRig Stops Working

« on: 2016-10-18, 06:41:58 »

You were right Mitschüler.
I called my isp and they aware this problem with pseudo IP and they promised that in 30 minutes they will change it.
Indeed after 1 hour all things as by magic worked as before.
So all OK.  Thank you for one more time for your kind support.  73 Dimitris

Sent from my SM-G925F using Tapatalk

12

General discussion forum / Re: Lost contact with Remote.

« on: 2016-10-02, 12:21:41 »

Hello Mitch you were right!!!
The new provider has given one pseudo IP in the router.
When i go to DMZ to specify an exception to firewall for my RRC the field has as IP this pseudo IP address 10.140.23 1 for example  and then 192.168.2. and an empty field where I put 228.
So what's next step? This telephone line belongs to a friend of mine and next Monday will try to contact them to see if they can help. If we have no result then what we can do? You said something for VPN? Please can you explain me how I can set it? Provider unfortunately cannot change as there is signed minimum agreement for 24 months. Thank U in advance  for your kind support. Dimitris DK1OZ

Sent from my SM-G925F using Tapatalk

13

General discussion forum / Re: New Problem Identified: Tip if RemoteRig Stops Working

« on: 2016-10-02, 12:20:26 »

Hello Mitch you were right!!!
The new provider has given one pseudo IP in the router.
When i go to DMZ to specify an exception to firewall for my RRC the field has as IP this pseudo IP address 10.140.23 1 for example  and then 192.168.2. and an empty field where I put 228.
So what's next step? This telephone line belongs to a friend of mine and next Monday will try to contact them to see if they can help. If we have no result then what we can do? You said something for VPN? Please can you explain me how I can set it? Provider unfortunately cannot change as there is signed minimum agreement for 24 months. Thank U in advance  for your kind support. Dimitris DK1OZ

Sent from my SM-G925F using Tapatalk

14

General discussion forum / Lost contact with Remote.

« on: 2016-10-01, 15:23:30 »

I have changed at the remote site provider but I use the same router with same parameters (opened ports).
From the moment they connected with my router remotely to setup their data for Internet I lost connection with my remote rig. I try today all day remotely to check all parameters in router and in RRC but all look correct. I changed the port numbers to default as per last edition manual but nix..
In my local RRC when I check status I see SIP error , Unknown SIP.
DDNS works OK and I see the IP of remote RRC.
My mind is empty from other ideas can anyone help?
I forgot to mention I use
Cmd port UDP 12200
AUDIO      UDP 11000
SIP            UDP 5065
Web          TCP  8080
TELNET    TCP  23

In router at FIREWALL DMZ is enabled and I have put the RRC address 192.168.2.228

Any help?

15

General discussion forum / Re: I cant connect with remote RRC site from my PC

« on: 2016-08-23, 19:29:35 »

I restarted the remote RRC locally and all is OK.

It needed to be restarted but only locally could be done because remotely I had not access.

Thank you for your soon and kind support.