Problem with TS-480

[Dave85]

I have a problem with TS-480.
I just test it on my network.
I have made ​​the configuration according to instructions.
When I press the power button there is a beep and the display will not turn on.
Then the yellow LED goes on and at the Radio and Control.
the LED at the Radio goes off again and then the unit restarts.
When I press the power button again then the screen goes on and displays "HELLO".
On Control and Radion is only the yellow LED on and I hear a noise.
Normally, the display shows me the frequencies.
What can I do?

These are the Staus Pages:

Control:

Name            Value
Control panel      ON
Radio            ON
SIP status         Connected/transfering
Last SIP error         None
RTP Timeout         57
SIP Timeout         0
Rx Jitter buffer size      4
Rx Jitter delay         3
Dual Rx            0
Current audio packet size   20
Current audio quality      2 - Linear 16 bits 8 kHz
SIP Out port         15077
SIP In port                 15077
Audio Out port         11000
Audio In port         11000
Command Out port      12000
Command In port         12000
External SIP In port      15077
External Audio In port      11000
External Cmd In port      12000
Other party         192.168.178.22
Input 0            High
Input 1            High
Input 2            High
Output 0         High
Output 1         Low
Output 2         Low
DNS status         OK, remoterig.com = 193.202.110.185
Active profile:         Default
PTT status:         OFF

Radio:
Status
Name            Value
Radio            ON
SIP status         Connected/transfering
Last SIP error         None
RTP Timeout         59
SIP Timeout         0
Rx Jitter buffer size      4
Rx Jitter delay         3
Dual Rx            0
Current audio packet size   20
Current audio quality      2 - Linear 16 bits 8 kHz
SIP Out port         15077
SIP In port                 15077
Audio Out port         11000
Audio In port         11000
Command Out port      12000
Command In port         12000
External SIP In port      15077
External Audio In port      11000
External Cmd In port      12000
Other party         192.168.178.36
Input 1            High
Input 2            High
Output 0             Low
Output 1         Low
Output 2         Low
DynDns status         Unknown
Ping status (watchdog)      Off
Active profile:         Default
PTT status:         OFF

[dj0qn]

Dave,

Did you set the jumpers as per the instructions on page 132? If so,
please double check them to make sure that you didn't wire them wrong
by accident. Pin 1 is on the top when the socket is on the right looking at
the RRC.

73,
Mitch DJ0QN / K7DX

[Dave85]

I replaced all the cables, according to the instructions on page 132.
Then I measured the crossing, all is ok.
What I noticed is, that at the Control side Pin4 is crossing  MIC-GND and GND and Pin 6 GND and MIC-GND.
Is that ok?
When I press the power button, the display will not start anymore.
On the control side the red and yellow LED's are on, but on the radio side only the red is shortly on and then the unit restarts.

[dj0qn]

I still think something is wired wrong, or else a jumper is broken. I know out of
personal experience that these jumpers are not as easy to place as they look.
I had some problems at first and had to replace two of them. Now I use needle-
nose pliers to set the last couple of mm in the hole, I learned my lesson.

If you are 100% sure that everything is correct, then I am afraid that the
RemoteRig team will have to step in and help you out.

73,
Mitch DJ0QN / K7DX

[va3mw]

Dave

I would reset both units and start again.  Go with the default settings, including the SIP ports. 

If that works, then start to modify it to suite your requirements.

Mike va3mw

[Dave85]

I solved this problem now.
The radio and the "Radio RRC" were connected to the same power supply.
When I press the "power button" the radio goes on and the RRC restarts.
That was also the reason why the display shows only "Hello."
The radio RRC is now connected to a separate power supply and it works well.

Many thanks for the replies.

Dave