Author Topic: RC 2000 - 0,1KHz step  (Read 24014 times)

EA5WA

  • Full Member
  • ***
  • Posts: 114
    • View Profile
    • Email
Re: RC 2000 - 0,1KHz step
« Reply #15 on: 2021-01-25, 20:21:00 »
Hi Willi:

I can see the link you posted.

I've just purchased an 600 pulses/rotation encoder from China. I'm going to make my first test....

I have Red (Vcc), Black (GND), White (A)and Green (B). Is that correct? Could I use your schematic?

73 de EA5WA Juan Carlos

73's from EA5WA Juan Carlos

DF1NP

  • Jr. Member
  • **
  • Posts: 48
    • View Profile
Re: RC 2000 - 0,1KHz step
« Reply #16 on: 2021-01-26, 11:03:40 »
Hi Juan Carlos,

Some pictures for wiring the 100 pps decoder:
A goes to internal decoder (red)
B goes to internal decoder (green)
OV goes to GND (yellow)
VCC goes to + 5V (orange)
A and B you can change
The colors belongs to the wire in the RC-2000 case not at decoder.

73
Willi

EA5WA

  • Full Member
  • ***
  • Posts: 114
    • View Profile
    • Email
Re: RC 2000 - 0,1KHz step
« Reply #17 on: 2021-01-26, 18:15:42 »
Very nice performed Willi. No resistors needed?

Many thanks for the info

I'll purchase an encoder like yours

73 de EA5WA Juan Carlos
73's from EA5WA Juan Carlos

DF1NP

  • Jr. Member
  • **
  • Posts: 48
    • View Profile
Re: RC 2000 - 0,1KHz step
« Reply #18 on: 2021-01-26, 19:28:10 »
Hi Juan Carlos,

No resistor necessary.

Btw. look at this:
http://dk8jg.de/VFO-Maus-3.pdf

73
Willi

EA5WA

  • Full Member
  • ***
  • Posts: 114
    • View Profile
    • Email
Re: RC 2000 - 0,1KHz step
« Reply #19 on: 2021-01-26, 19:35:35 »
How many pulses x rotation is your encoder.

First test with my 600 pulses x rotation encoder I think is too much. If you turn too fast, RRC goes crazy trying to count so many pulses....

73 de EA5WA Juan Carlos
73's from EA5WA Juan Carlos

DF1NP

  • Jr. Member
  • **
  • Posts: 48
    • View Profile
Re: RC 2000 - 0,1KHz step
« Reply #20 on: 2021-01-27, 09:43:48 »
One turn (360 degrees) = 100 pps. The 500 pps by my former encoder (HEDGE) was too much. That was the reason I changed to 100 pps. Pushing the small encoder you also can change the speed of the external encoder.

73
Willi

EA5WA

  • Full Member
  • ***
  • Posts: 114
    • View Profile
    • Email
Re: RC 2000 - 0,1KHz step
« Reply #21 on: 2021-01-27, 22:23:10 »
Waiting for a 100ppr encoder, today I've modified my RC-2000
73's from EA5WA Juan Carlos

DF1NP

  • Jr. Member
  • **
  • Posts: 48
    • View Profile
Re: RC 2000 - 0,1KHz step
« Reply #22 on: 2021-01-28, 20:25:36 »
Hi Juan Carlos,

nice pictures. Congrats and good luck.

73
Willi

EA5WA

  • Full Member
  • ***
  • Posts: 114
    • View Profile
    • Email
Re: RC 2000 - 0,1KHz step
« Reply #23 on: 2021-01-31, 13:07:44 »
I have a problem. I've just put my new 100 pulses encoder without resistors, and sometimes work, but sometimes doesn't work. Screen flashes following the pulses, but frequency doesn't change. Disconecting and conecting again the external encoder, RC-200 restarts....

Could be a power supply problem?

Any ideas?
 
73's from EA5WA Juan Carlos

EA5WA

  • Full Member
  • ***
  • Posts: 114
    • View Profile
    • Email
Re: RC 2000 - 0,1KHz step
« Reply #24 on: 2021-02-02, 18:46:58 »
Now with a 100 Ohms resistor in the VCC line is working fine.

Maybe my encoder is demanding too much power.

73 de EA5WA Juan Carlos
73's from EA5WA Juan Carlos

DF1NP

  • Jr. Member
  • **
  • Posts: 48
    • View Profile
Re: RC 2000 - 0,1KHz step
« Reply #25 on: 2021-02-02, 22:27:45 »
congrats, Juan Carlos  :)

73
Willi