Hello,
I'm helping to remote a friends station. Yesterday, he was at the remote end, I was at the shack with the controlled radio.
He purchased the K3-twin kit via Elecraft. They are full K3s on both ends.
We have everything connected according to the documentation, but no go. I have the router correctly forwarding ports.
Here's where I'm confused: I used a port scanner to scan the remote rig box using the local IP. It only shows port 80 open for HTTP and port 22 open for Telnet.
Ports 11000, 12000 and 5060 are not open. That would make sense since we cannot connect.
Of course, I can get to the unit's web page, and I can connect to the telnet port -- so it's alive.
Why would these ports not be open??
Here's what the Microbit status page says:
nfo
Name Value
Company Microbit
Product 1258
PID 4
Version 7
HW 8
Software 2.72
Bootloader 1.10
Compiler 4.6.2
Build May 13 2013 15:02:08
ROM/RAM 449196/41872
ETH-RAM 2944 (max 3kB)
USB-RAM 15312 (max 16kB)
ResetSrc 0 [3]
Uptime 53579
Serial number 6250
MAC address 00:1e:fd:01:8f:0a
IP address 192.168.1.170
Netmask 255.255.255.0
Gateway 192.168.1.1
DNS 192.168.1.1
Wi-Fi network module not present
Settings
Unit ID (Banner) ******* (redacted_
DHCP 0
IP 192.168.1.170
Netmask 255.255.255.0
Gateway 192.168.1.1
Dns server 192.168.1.1
Extern IP/Host ***** (redacted)
Eth-type 4
IP-interface 1
Web page user
Web page pwd
Program mode 14
Control panel 0
Sip password
Sip contact
Auto connect 0
Audio quality 3
Audio dual-rx 1
Codec out gain 250
Codec inp gain 32
Codec inp HPF Hz 3
Codec inp preamp 1
Codec inp attenuation 1
COM0 baudrate 9600
COM0 data bits 8
COM0 stop bits 1
COM0 parity 0
COM0 Program mode 3 char timeout 2
Use USB Com Port as COM0 0
COM1 mode 7
COM1 baudrate 38400
COM1 data bits 8
COM1 stop bits 1
COM1 parity 0
COM1 rts/cts 0
COM1 terminator (hex) 00
Use USB Com Port as COM1 0
COM2 mode 9
COM2 baudrate 9600
COM2 data bits 8
COM2 stop bits 1
COM2 parity 0
COM2 terminator (hex) 00
Use USB Com Port as COM2 0
COM3 mode (USB-COMFSK) 10
UDP cmd port 12000
UDP audio port 11000
SIP port 5060
Web server port 80
Telnet server port 23
Rx jitter buffer size 8
Rx jitter delay 4
Audio packet size (ms) 20
RTP tx mode 0
Debug level 0
Disable audio tones 0
Audio tones -db [70-0] 30
IP identification (morse) 0
Full duplex 0
PTT-off mute delay 0
IP Type-of-Service (dec) 0
Yaesu power-on/off 0
Elecraft advanced 0
UDP antenna-switch port 13010
UDP cmd min-data-size 0
Check interval 10
DDNS Host name 0
Own host name ****** (redacted)
Username
Password
Enable 0
Speed wpm [0/10-40] 0
Iambic 1
Paddle reverse 0
Weight [25-40] 30
Side tone hz [0,300-1500] 800
Side tone -db [50-0] 20
Lf delay ms [0-500] 0
Key delay ms [0-250] 0
PTT activated by Keyer 0
PTT tail delay ms [0-999] 0
Speed pot min wpm [5-99] 10
Speed pot max wpm [5-99] 40
IN0 mode 0
OUT0 mode 3
OUT0 mode 3
OUT1 mode 7
OUT1 mode 7
OUT2 mode 1
OUT2 mode 1
USB RTS as PTT 0
USB DTR as CW 0
Enable ping watchdog 0
IP address to ping
Ping interval (seconds) 300
Startup delay (seconds) 300
Failure count to reboot 3
1: Name (SSID)
1: Password (PSK)
2: Name (SSID)
2: Password (PSK)
3: Name (SSID)
3: Password (PSK)
4: Name (SSID)
4: Password (PSK)
5: Name (SSID)
5: Password (PSK)
6: Name (SSID)
6: Password (PSK)
7: Name (SSID)
7: Password (PSK)
8: Name (SSID)
8: Password (PSK)
Status
Name Value
Radio OFF
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 0
Rx Jitter buffer size 8
Rx Jitter delay 4
Dual Rx 1
External IP **** (redacted)
SIP Out port 1024
SIP In port 5060
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 0.0.0.0
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
Ping status (watchdog) Off
DNS status OK, remoterig.com = 193.202.110.185
Active profile: Default
PTT status: OFF
Antenna-Switch (IP) not connected
I presume we do not have to set any special menu settings on the K3?
Any help appreciated.
73, Gerry W1VE
